Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for joke MINI MONTOR mobile 1 P
Summary of Contents for joke MINI MONTOR mobile 1 P
- Page 1 Instruction Manual MINI MONTOR mobile 1 P Order No. 0 006 700...
-
Page 2: Table Of Contents
Please feel free to call our customer service department at any time should you encounter tech- nical problems which are not dealt with in this manual: Telephone: 0 22 04 / 8 39 - 0 Telefax: 0 22 04 / 8 39 - 60 Internet: www.joke.de... -
Page 3: Safety Instructions
The unit is designed exclusively for grinding work with the tools listed and approved in the joke catalogue for Surface Finishing. Any other use will be deemed to be contrary to its intended purpose. The manufacturer cannot be held liable for any resulting dama- ges. -
Page 4: Warranty/Identification
Warranty/identification joke Technology GmbH warrants the correct manufacture of every joke product which is deli- vered in accordance with the terms of contract and delivery. This warranty does not cover damages caused by normal wear and tear, incorrect handling, negligent use, the fitting of non-original spare parts, ina dequate care and/or a failure to comply with this technical manual. -
Page 5: Purpose
Purpose The Mini MONTOR mobile 1 P grinding, milling and polishing system is used in tool making and mould building and in mechanical workshops for fine surface finishing. The Mini MONTOR mobile 1 P set provides you maximum mobility during daily work. Well protec- ted in the hard-shell aluminium case, the grinding device can be taken anywhere. -
Page 6: Technical Data
Technical data Mobile 1 P Set Speed 1,000 - 33,000 rpm Motor carbon brush motor Dimension handpiece Ø 25 mm x 143 mm Weight handpiece 180 g (with cable) Weight control unit 300 g Collet Ø 3.0 mm (Ø 2.35 mm and Ø 3.175 mm in stock) Colour white Storage battery type... -
Page 7: Operation/Use/Care
Operation use Stand the control unit at a suitable safe, dry place. The ambient temperature should be between 0° and +40° C and relative humidity should be between 10 and 85 %. Once the control unit has been fully charged, remove the charger. Connect the hand- piece to the controller (7.1.3). - Page 8 Connecting the handpiece Never open the handpiece when the motor is running! The MPH33 micromotor handpiece is factory-fitted with a protective pin (7.4.1) to protect the collet. Fig. 7.4 changing tool Replace the tool with the protective pin by rotating the front section of the handpiece clockwise. The spacer can now be easily removed.
- Page 9 Rechange the battery Switch the device off (7.1.2). Connect the power supply unit/charger to the control unit (7.2.3) and the mains cable (5.1.6) to the charger and the mains supply. Charging takes approx. 1 hour. Replace a discharged battery with a new one when the battery no longer has sufficient capacity. The Ni-Mh battery can be recharged approx.
-
Page 10: Troubleshooting
• Reconnect the connecting cable to the control unit motor does not run. • Motor cable is faulty; replace motor cable • Motor is faulty; send in to joke for repair • Collet open; close collet. Motor suddenly stops • Hand/foot switch is set to „H“; select „F“. -
Page 11: Telefax Form
Please send us the spare parts drawing and parts list for the following equipment: as a printout (see address overleaf), by Fax, as a pdf file to my e-mail address. Set MINI MONTOR mobile 1 P Order No. 0 006 700 Mobile control unit MPC20-W Order No. - Page 12 Fax +49 (0) 22 04 / 8 39-60 Mail info@joke.de Web www.joke.de © Copyright joke Technology GmbH • August 2012 • All rights reserved for technical modifications, inaccuracies and printing errors. • Reprinting, even in part, only subject to prior written approval.
Need help?
Do you have a question about the MINI MONTOR mobile 1 P and is the answer not in the manual?
Questions and answers