Page 2
® -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 South-Tek Systems VERSION HISTORY Revision Implemented Revision Approved Approval Reason Date Date J. Nguyen 10/13/13 A. Norman 10/13/13 Initial Release J. Nguyen 7/5/14 A. Norman 7/5/14 J. Nguyen 8/15/14 A. Norman 8/15/14 J.
® -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 South-Tek Systems TABLE OF CONTENTS 1 INTRODUCTION ........................6 Purpose ........................6 Audience ........................6 Important Information ....................6 2 SAFETY GUIDELINES ......................7 General ........................7 Service ........................7 3 SYSTEM DESCRIPTION ...................... 8 Key Features ......................
® -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 South-Tek Systems 1 INTRODUCTION PURPOSE ® The N -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 (Type II Series), provide an economical, precise means of generating high purity nitrogen. Since air is comprised of ~79% N we simply and cost-effectively separate the N from the air.
® -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 South-Tek Systems 2 SAFETY GUIDELINES GENERAL ® Correct use of N -BLAST Nitrogen Generator is important for your personal ® safety and for trouble-free functioning of the N -BLAST Nitrogen Generator. ®...
® -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 South-Tek Systems 3 SYSTEM DESCRIPTION KEY FEATURES ® The N -BLAST Nitrogen Generator key features include the following: Air Filters and Pressure Regulator Membrane Pressure Switch for Automatic Start/Stop (per demand) Safety Relief Valve...
Identify and verify that all parts listed on the packing list are present and undamaged. South-Tek Systems (STS) is not responsible for damages that have ® occurred during the shipping and handling of the N -BLAST Nitrogen Generator.
Page 11
® -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 South-Tek Systems Figure 1: N2-Blast® Type II Series Wall Mount Diagram ® 1. Install the lower mounting bracket on the N -BLAST Nitrogen Generator by sliding the bracket through the keyway on the lower mounting flanges. (Item #3 into Item #4) a.
® -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 South-Tek Systems 4. An 110VAC power connection should be installed per local code by a qualified electrician. See the wiring diagram for specifics. Optionally a standard 110VAC power cord can be installed on the system by a qualified electrician.
® -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 South-Tek Systems adjustment is required. PANEL LAYOUT AND GAS CONNECTION Air Input is located on the left side of the unit. Nitrogen outlet will be located on the right side of the unit. Double-check all connection locations before turning on the system or opening any valves.
® -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 South-Tek Systems 5 SYSTEM USAGE INSTRUCTIONS ® The N -BLAST Nitrogen Generator is intended to be used to generate nitrogen and provide nitrogen for the fire protection piping system. Follow the installation instructions above and only use in an approved environment.
Page 15
® -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 South-Tek Systems the pipe lines, loose fittings, faulty connection, etc. These leaks are potential safety hazards, they can cause the nitrogen to deplete quickly, and could cause your N ® BLAST Nitrogen Generator to run in excess (decreasing the life of the unit).
Filter Replacement Kits can be purchased from South-Tek Systems that include the Filter Elements for the specified unit (STS Part # FRP-002). Prior to Filter Bowl Removal Ensure the power has been disconnected from the source.
Page 17
® -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 South-Tek Systems secure it in place with the threaded ring. 4) Before reinstallation of the filter bowl, be sure to clean out any debris with hot water and shake dry the water out.
® -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 South-Tek Systems 6) To reinstall the filter bowl, reverse the procedures used in removing the filter bowl. ® Reconnecting Your N -BLAST Nitrogen Generator: 1) After all filter elements have been replaced, wipe down all surfaces with a clean dry towel.
® -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 South-Tek Systems GAS LEAKS: As with any gas system, only use a spray bottle on non-electrical equipment to find leaks. Fix or replace leaking fittings or old hose. Push-to-connect fittings will show bubbles and typically have up to a 5ccm acceptable leakage rate.
RMA number (return authorization number) may be denied and returned to the sender. Contact the factory for RMA #’s, prior to return shipment. South-Tek Systems is not liable for damages caused by normal wear and tear, water, fire, erosion, corrosion, explosion, misuse, oil/gas vapors or unauthorized modifications.
® -BLAST Nitrogen Generator FPS-1750, FPS-3000, and FPS-6000 South-Tek Systems APPENDIX B: AUTO PURGE SYSTEM (APS) Installation and Quick Start Guide Auto Purge Assembly Settings Label Flow Setting Indicator Introduction to APS: The AutoPurge System™ is simple to install and requires little maintenance. This device...
Need help?
Do you have a question about the N2Blast FPS-1750 and is the answer not in the manual?
Questions and answers