Related Manuals for Taco Marine Grand Slam 280
Summary of Contents for Taco Marine Grand Slam 280
- Page 1 TACO Marine® Grand Slam Mounts GS-280 / 2801 Outrigger Mount INSTALLATION INSTRUCTION GUIDE ®...
-
Page 2: Kit Contents
KIT CONTENTS Grand Slam 280 mounts or Grand Slam 2801 mounts Required* *not included • Rotator Handles POWER DRILL WITH 5/16" DRILL BIT • 3/16" ALLEN WRENCH • 1/2" CRESCENT WRENCH Vinyl tubing spacers • MARINE-GRADE SEALANT • MARINE-GRADE GREASE OR ANTI-SEIZE •... -
Page 3: Installation Notes
GS-280/2801 Thank you for purchasing the TACO Marine Grand Slam 280 or 2801 Outrigger Mount! As a family-owned and operated business since 1959, we take pride in offering the highest-quality, innovative products with excellent customer service. We stand behind our products 100 percent. If you have any questions about this mount or installation, please contact us by visiting tacomarine.com/contactus. -
Page 4: Installation
INSTALLATION HARDTOP Always use high-quality, stainless-steel hardware when mounting the base. Do not attempt to weld the base to any surface. 1. If you have a foam or core-filled hardtop make sure its thickness does not exceed 3". 2. The starting, or at-rest position of the outrigger is facing aft. The handles of the Grand Slam are set in the same position at the factory. - Page 5 FIGURE 1 5/16 x 18 Bolt (B) Stainless Steel Washer (E) Plastic Washer (D) Hard Top Spacer Tube (not included) Backing Plate (not included) Stainless Steel Washer (E) 5/16” x 18 Hex Nut (C) Hex Bolt (F) Rotator Handle (A) Hex Bolt (F) 12.
- Page 6 INSTALLATION SOFT TOP 1. To find the proper location of the mounting plate keep in mind that the handle of the GS-280 and 2801 requires 9-1/2" of clearance from the center of the 3-1/8" hole in order to rotate the outrigger 90º...
-
Page 7: Technical Specs
TECHNICAL SPECS Figure 1 (A) Knob should face port or starboard 5/16 x 18 Bolt (B) Stainless Steel Washer (E) Plastic Washer (D) Hard Top Spacer Tube (not included) Backing Plate (not included) Stainless Steel Washer (E) 5/16” x 18 Hex Nut (C) Hex Bolt (F) Rotator Handle (A) Hex Bolt (F) - Page 8 LOOSENING BASE MAINTENANCE If the 9/16" bolt on your GS-280 or GS-2801 loosens, please follow these steps to tighten the base. • Remove the two hex head screws from the handle with an Allen wrench • Remove the handle • NOTE: you can get to the top screw easier if you pull down on the handle and move it so it is in-between positions •...
-
Page 9: How To Use
How to use When fishing with the Grand Slam 280 or 2801, easily raise and lower outrigger poles by turning the knob on the outboard side of each mount, which will loosen for manual adjustment and then tighten to secure the outrigger position. For going under bridges, trailering or storage, we recommend lowering the outriggers to ensure they don't get damaged. -
Page 10: Need Support
We’re here to help. Need Support? Contact Us 1.800.653.8568 support@tacomarine.com tacomarine.com 50 NE 179th ST Miami, FL. 33162 @tacomarine @taco_marine TACO Marine ® 1 0 / GS - 28 0 / 28 01 OU TR IGG E R MOU NT... -
Page 11: Drill Template
GS-280/2801 Drill Template GS-280/2801 Drill TemplaTe Please print at 100 percent for accurate sizing. Slight scaling may still occur. Therefore, before drilling, it is recommended that all template dimensions be measured for accuracy. G S -2 80 / 2 801 OU T RI G G E R MO U N T / 1 1... - Page 12 ®...