AMX Modula Quick Start Manual

Overview
Because the Modula Distribution Matrix is available in various sizes and board
configurations, the illustrations in this guide may differ from the model(s) you
purchased. The Modula Instruction Manual contains complete documentation for this
product (including individual board specifications); see the AMX AutoPatch Software &
Documentation CD or visit www.amx.com.
General Specifications
Specifications
Approvals
AC Power
Power Consumption 3 RU
Power Consumption 4 RU
(depending on model)
Operational Temperature
Humidity
Dimensions 3 RU
Dimensions 4 RU
Weight
Installation
ESD Warning: Avoid ESD (Electrostatic Discharge) damage to
sensitive components; be sure you and the enclosure(s) are
properly grounded before touching any internal materials.
Rack Mounting
To rack mount a Modula enclosure:
1. Attach the rack ears as shown in FIG. 1 (screws provided).
2. Install in a rack leaving a minimum of one empty rack unit above and below
(required); three empty rack units above and below are recommended.
FIG. 1 Attach rack ears to side of enclosure
Linking Multiple Enclosures (if applicable)
If the system has multiple enclosures, an "AutoPatch Distribution Matrix Linking Quick
Start Guide" has been provided. Link the enclosures according to the guide.
Attaching Input & Output Cables/Wires
For testing purposes, attach just the first two sources and destinations according to the
Connector Guide. Follow the guide exactly; the system is programmed to operate
based on the guide.
CatPro or Cat-5 Boards – RJ-45
If the system includes CatPro or Cat-5 boards, information on attaching connectors
and setting up systems is provided in the Modula Instruction Manual.
Video Boards – BNC
Video BNC connectors are used for standard video, HV sync, Y/c, component,
wideband, SD-SDI, and HD-SDI.
Component signals (e.g., Y/Pb/Pr or RGsB) require more than one BNC connection.
The example in FIG. 2 (top of next column) shows three BNC cable connectors
attached for routing a three-component signal as Input 1.
AutoPatch Modula Distribution Matrix
CE, UL, cUL
100 - 240 VAC single phase (50 - 60 Hz)
3.3 A @ 115 VAC max.
1.6 A @ 230 VAC max.
260 W (max.), 100 W (typical) per enclosure
520 W (max.), 255 W (typical) per enclosure
260 W (max.), 105 W (typical) per enclosure
32° - 110° F (0° - 43° C)
0 to 90% non-condensing
Approximately 17.0 in. (43.18 cm) depth
18.8 in. (47.7 cm) width with mounting ears
17.4 in. (44.2 cm) width without mounting ears
5.3 in. (13.4 cm) height
Approximately 17.0 in. (43.18 cm) depth
18.8 in. (47.7 cm) width with mounting ears
17.4 in. (44.2 cm) width without mounting ears
7.0 in. (17.8 cm) height
Approx. 22 - 24 lb. (9.98 - 10.88 kg) per enclosure
FIG. 2 Three BNC connectors are required for a three-component signal
S-Video Boards
S-Video boards are equipped with locking connectors, which lock into AutoPatch
S-Video cables. Standard S-Video connectors may be used, but will not lock.
To fasten a locking S-Video connector:
the right while pushing in or pull back on the connector housing while pushing the
connector in.
FIG. 3 Pull back on connector housing while pushing in
RGBHV/HD-15 Boards
RGBHV/HD-15 boards use the pinouts in FIG. 4 for HD-15 connectors.
FIG. 4 HD-15 input and output board connector pinouts
Note: Power draw not to exceed 50 mA per port.
Stereo Audio Boards – 5-Term
Stereo audio boards with 5-position terminal block connectors can be wired for
balanced (differential) or unbalanced (single-ended) audio (see FIG. 5).
FIG. 5 Balanced audio
Note: When using a shielded twisted-pair cable, connect the shield (ground) at one
end only (recommend receiving end) to minimize low frequency noise (see FIG. 6).
Source and destination devices will require either balanced or unbalanced
connections. More than one of the options shown in FIG. 6 can be used in the same
system.
FIG. 6 Options for source-to-Modula-to-destination 5-Term wiring
Quick Start Guide
hold the connector at a slight angle to
Connector housing
Unbalanced audio