Related Documents - AMX Modero MVP-8400 Quick Start Manual

Configuring the Panel's Wireless IP Settings
The first step is to configure the wireless communication parameters, this only
configures the card to communicate to a target WAP, it is still necessary to tell the
panel which Master it should be communicating with; see
Consult the MVP-7500/8400 Modero ViewPoint Touch Panels Operation/Reference
guide for setting the wireless communication using a static IP address.
Wireless communication using a DHCP Address
In the Protected Setup page:
1. Select Wireless Settings. Wireless communication is set within the IP Set-
tings section of this page.
2. Toggle the DHCP/Static field (from the IP Settings section) until the choice
cycles to DHCP. This action causes all fields in the IP Settings section (other
than Host Name) to be greyed-out.
Do not alter any of these remaining greyed-out fields in the IP Settings section. Once
the panel is rebooted, these values are obtained by the unit and displayed in the
DNS fields after power-up.
Consult the MVP-7500/8400 Modero ViewPoint Touch Panels Operation/Reference
guide for setting a Host Name.
Configuring the Card's Wireless Settings
This section configures both the communication and security parameters from the
internal wireless card to the WAP.
Once you have set up the wireless card parameters, you must configure the
communication parameters for the target Master; see
Consult the MVP-7500/8400 Modero ViewPoint Touch Panels Operation/Reference
guide for configuring the wireless card for unsecured access to the WAP.
Configuring the Wireless Card for Secured Access to the WAP
In the Protected Setup page:
1. Select Wireless Settings.
2. Enter the SSID information automatically by pressing the Site Survey button.
3. Select a WEP secured WAP from within the Site Survey page, and press the
Connect button.
4. Write down the SSID name, Current Key string value, and panel MAC Address
information so you can later enter it into the appropriate WAP dialog fields in
order to "sync-up" the secure connection. These values must be identically
reproduced on the target WAP.
Consult the MVP-7500/8400 Modero ViewPoint Touch Panels Operation/Reference
guide for manually entering the SSID information.
Master Connection
The panel requires you establish the type of connection you want made between it
and your master. In the Protected Setup page:
1. Select System Settings
2. Select Type to toggle between USB and Ethernet.
3. When using Ethernet, press the listed Mode to toggle through the
available connection modes:
Connection Modes
Mode Description
Auto The device connects to the first
master that responds. This
setting requires you set the
System Number.
URL The device connects to the
specific IP of a master via a
TCP connection. This setting
requires you set the Master's
IP.
Listen The device "listens" for the
master to initiate contact. This
setting requires you provide
the master with the device's IP.
4. Select the Master Port Number to open the keypad and change this value. The
default setting for the port is 1319.
5. Set your Master Port and select Done.
If you have enabled password security on your master you need to set the
username and password within the device.
6. Select the blank field Username to open the keyboard.
7. Set your Username and select Done.
8. Select the blank field Password to open the keyboard.
9. Set your Password and select Done.
10. Press the Back button to return to the Protected Setup page.
11. Press the Reboot button to reboot device and confirm changes.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
Master Connection
Master Connection
Procedures
Setting the System Number:
1. Select the System Number to open the
keypad.
2. Set your System Number select Done.
Setting the Master IP:
1. Select the Master IP number to the
keyboard.
2. Set your Master IP and select Done.
Confirm device IP is on the Master URL
list. You can set the Host Name on the
device and use it to locate the device on
the master. Host Name is particularly
useful in the DHCP scenario where the IP
address can change.
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
©2008 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
Touch Panel Calibration
In the Protected Setup page, follow these steps:
1. Select Calibrate.
.
2. Touch each target on the screen as they appear. Once calibrated the panel
confirms and instructs you to touch the screen to continue.

Related Documents

• MVP-7500/8400 Modero ViewPoint Touch Panels Operation/Reference Guide
• MVP-TDS Table Docking Station Operation/Reference Guide
• MVP-WDS Wall Docking Station Operation/Reference Guide
• MVP-KS KickStand Operation/Reference Guide
• VisualArchitect Operation/Reference Guide
• G4 PanelBuilder Operation/Reference Guide
• TPDesign4 Touch Panel Design Program Operation/Reference Guide
Caution: There are particular operations, such as upgrading the NXA-CFSP
compact flash card and replacing/installing the NXA-WC80211GCF Wireless
Compact Flash Card, that require opening the MVP's outer housing to access
internal components (as described in the MVP-7500 Modero ViewPoint Touch
Panels Operation/Reference Guide).
When opening the MVP panel housing to access internal components, be careful not
to damage or disconnect the wireless compact flash card antenna, which is mounted
to the inside of the rear housing.
.
10/08
93-5965-02 REV: R