AMX MVP-7500 Quick Start Manual

For more detailed installation instructions refer to the MVP-7500 and
MVP-8400 Modero ViewPoint Touch Panels Instruction Manual, available
on-line at www.amx.com.
FIG. 1
MVP-KS Kickstand for MVP Touch Panels (FG5965-12)
Overview
The MVP-KS Kickstand (FG5965-12) is compatible with both MVP touch panel
models: MVP-7500 and MVP-8400. This device provides the ability to easily rest
an MVP onto any flat level surface.
By connecting and securing the MVP-KS to the rear of the MVP, you are
now able to use the kickstand's rubber grip to provide a "grip" on the
desired level surface.
The MVP-KS mounts easily to the rear of the MVP by using both a set of
alignment guide pins and a retractable latch to secure the kickstand to the MVP.
Retractable
latch
Alignment
guide pins
FIG. 2
MVP-KS components
Specifications
MVP-KS Specifications
Dimensions (HWD): • Fully collapsed: 6.34" x 7.91" x 0.59" (16.10 cm x 20.10 cm x 1.50 cm)
• Fully extended: 6.34" x 7.91" x 4.17" (16.10 cm x 20.10 cm x 10.60 cm)
Weight: • 0.67 lbs (0.30 kg)
Components: • Retractable Latch: This latch grabs onto the metallic plate located on
the rear of the MVP and secures the MVP-KS to the panel.
• Release Lever: This lever is used to retract the MVP-KS lever and
release the secured MVP touch panel.
• Support Arm: This adjustable support arm is used to provide a level
surface support for any MVP attached to the MVP-KS.
Operating/Storage • Operating Temperature: 0° C (32° F) to 40° C (104° F)
Environments: • Operating Humidity: 20% - 85% RH
Included
• MVP-KS Kickstand for MVP Touch Panels Quick Start Guide
(93-5965-12)
Accessories:
Optional • MVP-7500 7.5" Modero ViewPoint Touch Panel (FG5965-01)
Accessories: • MVP-8400 8.4" Modero ViewPoint Touch Panel (FG5965-02)
Securing an MVP to the MVP-KS
1.
2.
3.
Alignment
FIG. 3
4.
MVP latch release lever
5.
6.
Support
arm (with
rubber grip)
FIG. 4
7.
Note: Upon proper connection, you should hear a "click" when the latch
securely "grabs" onto the metallic plate.
8.
9.
Note: The black rubber strip on the bottom of the support arm provides the
MVP/KS combo with added surface grip.
CAUTION: Be very careful when testing the proper connection of the MVP
to the MVP-KS. If the panel is not securely attached, the MVP could
suddenly become detached and be damaged.
MVP-KS
Kickstand for MVP Touch Panels
Place a soft cloth onto a level surface.
Carefully place the MVP panel onto the cloth in order not to scratch
the panel during the installation process.
Locate the MVP-KS alignment guide pins (FIG. 3). These pins are
inserted into the respective MVP alignment guide insertion holes
(located along the underside of the MVP - at either sides of the
connector strip).
guide
insertion
holes
Alignment
guide pin
Aligning the MVP panel to the kickstand alignment guide pins
Carefully grasp both sides of the MVP-KS Kickstand and insert the KS
alignment guide pins into their respective insertion holes on the
bottom of the MVP (FIG. 3).
Maintain a kickstand connection to the bottom of the MVP panel
(FIG. 4).
Use downward pressure on the MVP-KS' AMX logo to insert the
retractable latch into the opening just above the MVP metallic plate
(FIG. 4).
KS connection site #2
(latch secures to the
metallic plate on the
MVP)
Installing an MVP-KS onto the back of an MVP panel
Verify a secure connection between the MVP and the kickstand.
Extend the MVP-KS support arm (as seen in FIG. 1).
Carefully grab both sides of the MVP panel and rotate the entire unit
over back onto the level surface.
Quick Start Guide
MVP connector
strip
MVP battery
compartment
MVP rear
metallic plate
(where the KS
latch secures
the panel)
Alignment
guide pin
KS connection site #1
(to alignment pins)