AMX Modero NXD-CV7 Quick Start Manual

For more detailed installation, configuration, programming, file transfer, and
operating instructions, refer to the NXD-CV7/NXT-CV7 Instruction Manual,
available on-line at www.amx.com.
NXD panel
(WallMount)
FIG. 1
7" Modero Widescreen Video Touch Panels
ATTENTION!
Verify you are using the latest NetLinx Master and Modero touch panel firmware
(available from www.amx.com). Verify the TPDesign4 program being used is
Version 2.6 or higher.
Overview
These are the first 7" diagonal Widescreen Color Active video-capable touch
panels in the control and automation industry. These Color Video (CV) panels
display NTSC/PAL/SECAM video formats within variable sized windows. They
include a built-in microphone, speakers, audio/headphone connector, and six
NetLinx programmable pushbuttons (available on NXD models only when
mounted with included Button Trim Ring).
Table Top models use AMX's exclusive SmoothTilt™ technology for effortless
adjustment of the viewing angle.
Each panel is sold only as part of a CV7 Kit which includes both a panel and an
NXA-AVB/ETHERNET Audio/Video Breakout Box (FG2254-10) although the
breakout box can be purchased separately. The following bullets list the two
available Kit configurations:
• NXD-CV7 (FG2258-02K) - 7" Wall Mount Touch Panel Kit
(includes an NXD panel and NXA-AVB/ETHERNET A/V Breakout Box).
• NXT-CV7 (FG2258-01K) - 7" Table Top Touch Panel Kit
(includes an NXT panel and NXA-AVB/ETHERNET A/V Breakout Box).

Specifications

CV7 Specifications
Dimensions (HWD):
NXD-CV7 • Faceplate included: 5.93" x 7.87" x 3.28"
(15.06 cm x 20.00 cm x 8.33 cm)
(FG2258-02)
• Fully raised: 6.86" x 7.96" x 6.93" (17.40 cm x 20.20 cm x 17.60 cm)
NXT-CV7
Fully lowered height: 3.70" (9.40 cm)
(FG2258-01)
• Conduit/wallbox: 5.47" x 7.23" x 3.40"
CB-TP7
(13.90 cm x 18.40 cm x 8.64 cm) (optional)
(FG035-10)
Power Requirements • Constant current draw: 1.0 A @ 12 VDC (stand-alone)
• Startup current draw: 1.5 A @ 12 VDC (stand-alone)
(stand-alone CV7):
Power Requirements
• Constant current draw: 2.4 A @ 12 VDC
(CV7 and BASE/1): • Startup current draw: 3.6 A @ 12 VDC
Minimum power • PSN2.8 Power Supply (FG423-17)
- when used with a stand-alone CV7 unit.
supply required:
• PSN4.4 Power Supply (FG423-45)
- when a CV7 is connected to a BASE/1. Using accessories can
increase the power draw requirements.
Memory: • 64 MB SDRAM
• 64 MB Compact Flash (upgradable to 1 GB - factory programmed)
Weight: • 4.12 lbs (1.87 kg)
Certifications: • FCC Part 15 Class B and CE
Panel LCD • Aspect ratio: 16 x 9
• Brightness (luminance): 350 cd/m2
Parameters:
• Channel transparency: 8-bit Alpha blending
• Contrast ratio: 200:1
• Display colors: 256 thousand colors (18-bit color depth)
• Dot/pixel pitch: 0.19 mm
• Panel type: TFT Color Active-Matrix
• Screen Resolution: 800 x 480 pixels (HV) @ 60 Hz frame frequency
• Video format: NTSC, PAL, and SECAM
Viewing Angle: • 100° total viewing angle
• Vertical: + 50° (up from center) and -50° (down from center)
IR Reception Angle: • Horizontal: + 50° (left and right from center)
• Vertical: + 30° (up and down from center)
Supported Audio • 48000Hz, 44100Hz, 32000Hz, 24000Hz, 22050Hz, 16000Hz,
12000Hz, 11025Hz, and 8000Hz.
Sample Rates:
7"
Modero Widescreen Video Touch Panels (G4)
CV7 Specifications (Cont.)
Front Panel:
NXT panel
(Table Top)
Rear Connectors:
Operating /Storage
Environments:
Included
Accessories:
Other AMX
Equipment:
Panel Connectors
FIG. 2 shows the connectors located on the CV7 Modero Video panels. The
Audio/Video RJ-45 connector provides differential audio/video signals between
the touch panel and the NXA-AVB/ETHERNET. This connector routes
Composite video, Stereo (left/right) audio, and microphone audio.
P R O G R AM
Mini-USB
(Program Port)
Stereo
Output
FIG. 2
Connector layout on the CV7 Touch Panels
NXA-AVB/ETHERNET Breakout Box
FIG. 3 shows the front and rear connectors on the NXA-AVB/ETHERNET
breakout box. This breakout box can be mounted on either a horizontal flat
surface or in an equipment rack (by removing the front faceplate and securing it
to an optional AC-RK Rack Kit).
Quick Start Guide
• Light Sensor: Photosensitive light detector for automatic adjustment of
the panel brightness
• Motion Sensor (PIR): Proximity Infrared Detector to wake the panel
when panel is approached
• IR Receiver: 38 KHz and 455 KHz AMX IR frequencies
• Sleep Button: Pushbutton (grey) provides both access to the Setup
and Calibration page and toggles the panel between a "sleep" or
"wake" state
• Microphone: Used for intercom applications (requires the
NXA-AVB/ETHERNET Breakout Box for analog communication)
• Speakers: Stereo output with a frequency response of 500 Hz - 7 KHz
• LEDs: 6 blue LEDs (support On and Off)
- Both the LEDs and pushbuttons are only available when using
the default Button Trim Ring on the NXD panel.
• Buttons: 6 programmable pushbuttons
• Mini-USB Connector: 5-pin Mini-USB connector used for
programming, firmware update, and touch panel file transfer between
the PC and the target panel
• Stereo Output Connector: Stereo output through a 3.5mm mini-jack
(for use with external speakers or headphones)
• Ethernet 10/100 Port: RJ-45 port for 10/100 Mbps communication
• USB Connector: Type A USB port connects an external keyboard or
mouse device for use with Virtual PC applications
• Audio/Video Connector: RJ-45 connection for A/V signals (via CAT5)
between the NXA-AVB/ETHERNET Breakout Box and the panel
• Power: 2-pin 3.5 mm mini-Phoenix connector
• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% - 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH
• Installation Kit for NXD-CV7 panels (KA2258-02):
- 2-pin 3.5 mm mini-Phoenix connector (41-5025)
- Two Phillips-head screws (#4-40 x 0.250 Black) (80-0112)
- Three Drywall clips (62-5924-05) and #6 - sheet metal screws
(80-0192)
• Installation Kit for NXT-CV10 panels (KA2258-01):
- 2-pin 3.5 mm mini-Phoenix connector (41-5025)
• Modero Table Top Cable (CA2250-50) provided with all NXT panels
• NXA-AVB/ETHERNET Breakout Box (FG2254-10)
- Provides video/audio distribution to the A/V panel over CAT5 cable
(up to 200'/60.96 m) and accepts either Composite or S-Video
• Trim Ring with button openings (60-2258-16)
(factory installed on NXD models only)
• Trim Ring without button openings (60-2258-21) (NXD models only)
• CB-TP7 Conduit/Wallbox (FG035-10)
• CC-USB (Type A) to Mini-B 5-Wire programming cable (FG10-5965)
• NXA-BASE/1 Battery Base Kit (FG2255-05K):
- battery base and single NXT-BP battery
• NXA-RK7 Rackmount Kit for 7" Wall Mount panels (FG2904-53)
• NXA-WC80211GCF, 802.11g Compact Flash Wireless Card Upgrade
Kit provides wireless Ethernet support (FG2255-07)
• NXT-BP Battery (FG2255-10)
• NXT-CHG Kit (FG2250-50K): single charger and 2 NXT-BP batteries
• PSN2.8 Power Supply (12 VDC) (FG423-17)
• PSN4.4 Power Supply (12 VDC) (FG423-45)
• Upgrade Compact Flash (factory programmed with firmware):
NXA-CFSP128M - 128 MB compact flash card (FG2116-36)
NXA-CFSP256M - 256 MB compact flash card (FG2116-37)
NXA-CFSP512M - 512 MB compact flash card (FG2116-38)
NXA-CFSP1GB - 1 GB compact flash card (FG2116-39)
A L
E TH E R N E T
K E Y B O A R D /
10/100
M O U S E
Audio-Video from
Ethernet
Keyboard/Mouse
(CAT5) NXA-AVB/ETHERNET
USB connector
12V DC
P W R
A U D IO / V ID E O
Power
(CAT5)