DELTA DORE TYDOM 2.0 Installation Manual
Ip/gsm home automation transmitter
Hide thumbs
Also See for TYDOM 2.0:
- Installation manual (196 pages) ,
- User manual (148 pages) ,
- User manual (63 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DELTA DORE TYDOM 2.0
Summary of Contents for DELTA DORE TYDOM 2.0
- Page 1 TYDOM 2.0 IP/GSM home automation transmitter Installation guide...
- Page 2 Package contents TYDOM 2.0 Mains adaptor Ethernet antenna cable Guides Documents Installation User SIM card Important Lithium battery ready to use Product LSH20 3.6 V Information CAUTION : Contains parts and assemblies susceptible to damage by Electrostatic Discharge (ESD). Observe precautions for handling electrostatic discharge sensitive devices.
-
Page 3: Table Of Contents
3.6 Activation ..........................13 of card. 3.7 Close TYDOM 2.0 ........................14 Maintenance mode: 4. Associate TYDOM 2.0 with the CS 8000 TYXAL+ alarm control unit ........14 The Maintenance mode is used for activation, 5. Personalising TYDOM 2.0 ......................15 'Internet protocol' maintenance and diagnostic operations. This mode 5.1 Naming TYDOM 2.0 ......................15... -
Page 4: How Does Tydom 2.0 Work
APPLICAZIONE TYDOM application TYDOM 2.0 is connected to a GSM telephone TYDOM 2.0 and other products in the TYXAL+ range, intrusion detectors, technical detectors, sirens, key- network and to the Internet via an ADSL box. IOS and Android pads or remote controls will be associated with the CS 8000 TYXAL+ alarm control unit (50 products max.). -
Page 5: Description
2. Description Association button Front panel and system LED Upper cover S1 S2 Lower cover Unit locking Socket cover 1- Battery compartment 6- SIM card slot 10- Microphone 2 - Tamper alarm on opening 7- T3 RESET button 11- System diagnostic LEDs 3- Mains adapter connection 8- Loudspeaker 12- Ethernet port... -
Page 6: Installation
Do not use an electric screwdriver to screw in the B screw 3.2 TYDOM 2.0 MAC address Before mounting TYDOM 2.0, note down the last 6 characters of the MAC address of your TYDOM 2.0. before configuring the TYDOM application. MAC : 001A25xxxxxx... -
Page 7: Sim Card (Mini Sim Format + Voice And Text Message Package)
1- Place TYDOM 2.0 on the wall mount. 2- Attach the unit with the 2 screws TYDOM 2.0 is connected to a GSM telephone network. Ø 4 mm max. using holes C. If a problem is detected, a text message is sent to the numbers in the contact list. -
Page 8: Close Tydom 2.0
The switch to maintenance mode automatically and briefly activates the indoor siren of the announced in the event of an alert. Name Personalise alarm control unit as well as a TYDOM 2.0 call cycle (configurable with CLT 8000 TYXAL+). Reception Alley Name... -
Page 9: Activating/Deactivating Tamper Alarm
'Browse'. Activate > Tamper alarm Entrance timer Ì Press the button of TYDOM 2.0 or select it from Í Once the product is identified, select the Back Back the list of products by clicking on 'Browse'. -
Page 10: Configuring The Sim Card
The auto attendant enables you to obtain voice information on the status of your installation when you are near your TYDOM 2.0 (e.g. "your alarm system is on"). This menu is used to enter the PIN code of the SIM card to activate it. -
Page 11: Maintenance Call
001A25FFFF123456 5.10 Alarm control unit monitoring Monitoring is used to trigger a call if TYDOM 2.0 does not receive information from the alarm control unit for more than 4 hours. This function, activated by default is configurable by calling the installation. -
Page 12: Information And Assistance
7. Information and assistance 8. Association of home automation functions 7.1 Meaning of LEDs The home automation functions remotely enable • Detailed daily consumption display (heating, hot (maintenance mode) you to: and cold water, gas, electricity) and history log per - Adjust house temperature (with 32 heat sensors day/week/month/year T1 - System status... -
Page 13: Correct Operation Test
10.1 Mains power failure Switch on the system, and trigger an intrusion. Allow After 5 minutes of power failure, TYDOM 2.0 sends a notification to the alarm the call cycle to run without touching the OFF button of control unit. The alarm control unit beeps. -
Page 14: Battery Replacement
11. Battery replacement 12. Advanced functions A message is sent to the CLT 8000 TYXAL + keypad to alert that the TYDOM 2.0's battery is empty. Switch the alarm control unit to MAINTENANCE mode (see system guide). The alarm control unit beeps each time the system is activated or deactivated, (or “battery defect” with the Open the TYDOM 2.0 unit. -
Page 15: Technical Characteristics
Electrical characteristics AC : AC : 100 – 240V~, 50/60 Hz, 0.4A - DC : 5V , 2A Only this adaptator should be used by TYDOM 2.0. SAFT LSH20 - 3,6V - 13 Ah - Lithium The intercom quality is poor TYDOM 2.0 runs a call cycle when... -
Page 16: Remote Monitoring Annex (Optional Feature)
TYDOM 2.0 www.deltadore.com Remote monitoring annex (optional feature) -
Page 17: Introduction
When an event is to be sent to the alarm receiving centre and only Ethernet is enabled, the Ethernet transmis- Information sent by TYDOM 2.0 to the remote monitor is sent via a main number and, in the case of a sion configuration is as follows: problem with the main line, a backup number. -
Page 18: Protocol Dc09 Configuration
1) Set the alarm control unit to “Maintenance” mode midnight). 2) Call the TYDOM 2.0 using a remote line and enter the installer code. To programme the cyclic test: 3) When the numbered main menu appears, enter “#” followed by the setting number - dial "#94”... -
Page 19: Personalising Tydom 2.0
Transmitter line number: Date : ....................Monitoring triggers a call if TYDOM 2.0 does not receive information from the alarm control unit for more Client / Address: ..................................than 4 hours. This function is enabled by default. Remote monitor / Tel. No. / person to contact: ...................... - Page 20 Page to send to remote monitor if your communication protocol is: Contact ID Page to send to remote monitor if your communication protocol is: DC09 P20 IP/GSM transmitter configuration IP/GSM transmitter configuration TYDOM 2.0 TYDOM 2.0 Date : .......... Contact ID 12 - 13 protocol...
- Page 21 IP DC09 P20 protocol - continued Additional parameters In accordance with ANSI/SIA DC09 2013, TYDOM 2.0 will also send the following parameters (in the XData field of the protocol): Example Time of Occurrence “H” Time of event 17:29:44,03/13/2019 Alarm Text “I”...
- Page 22 www.deltadore.com...