M-Audio MICRO DAC 24/192 User Manual

Technical Specifications
Outputs: (1) analog 1/8" (3.5 mm) headphone, (1) combination digital/optical
+ analog 1/8" (3.5 mm) headphone
Bit Depth / Sampling Rate: 24-bit / 192 kHz
Power: via USB connection
Minimum System Requirements: Windows 7 or Mac OS X 10.8; (1) Hi-Speed
USB 2.0 port
Dimensions (WxDxH): 2.8" x 0.9" x 0.4" / 70 x 24 x 10 mm
Weight: 0.06 lbs. / 0.03 kg
Specifications are subject to change without notice. Manual Version 1.0
Notice Concerning FCC Regulations: You are cautioned that changes or modifications
not expressly approved by the part responsible for compliance could void the user's
authority to operate the equipment. This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures: (a) Reorient or relocate the receiving antenna; (b) move this unit; (c) increase the
separation between the equipment and receiver; (d) connect the equipment into an outlet
on a circuit different from that to which the receiver is connected; (e) be sure that all cables
are properly shielded, using a choke or ferrite where appropriate; (f) consult the dealer or an
experienced radio/television technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment. End users must follow the
specific operating instructions for satisfying RF exposure compliance. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter. For
best audio quality, avoid using this device in a high RF-radiated environment. RSS
Statement for Canadian models: This device complies with Industry Canada licence-
exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device This unit does not
exceed the Class B limits for radio noise emission from digital apparatus set out in the radio
interference regulations of the Canadian Department of Communications.
ESD/EFT Warning: This unit may contain a microcomputer for signal processing
and control functions. In very rare situations, severe interference, noise from an
external source, or static electricity may cause it to lock up. In the unlikely event
that this should happen, turn off the unit, wait at least five seconds, and then turn
it back on again. In an environment with radio frequency interference, the unit
may malfunction and resume normal operation after removal of the interference.
User Guide
(English)
For more information about this product (system requirements, compatibility
information, etc.), product registration, or product support, visit m-audio.com.
For safety and warranty information, visit m-audio.com/warranty.
Package Contents: Micro DAC 24/192, USB Extension Cable, Carrying
Pouch, User Guide
Windows users: Visit m-audio.com/drivers
Windows driver for Micro DAC 24/192.
5
1
1. USB Port: Insert this connector to a USB port on your computer
(powered on). The connection will supply the necessary power to
Micro DAC 24/192.
If necessary, use the included USB extension cable so Micro DAC
24/192 does not block any adjacent connections on your computer.
2. Power Indicator: This light illuminates when Micro DAC 24/192 is
powered on.
3. Headphone Output: Connect standard 1/8" (3.5 mm) high-impedance
stereo headphones (32–150 Ω) to this analog output.
4. Headphone/Digital Combination Output: Use a 1/8" (3.5 mm)
optical/digital cable to connect this output to the digital input of a
receiver or playback device. Alternatively, connect standard 1/8" (3.5
mm) low-impedance stereo headphones (16–32 Ω) to this output.
5. Volume: Use this knob to adjust the volume level of the headphone
output and headphone/digital combination output.
Note: Alternatively, adjust the volume level on your connected
headphones, receiver or playback device, or your computer's sound card.
6. 192kHz Indicator: This light illuminates when the Micro DAC 24/192
sampling rate is set to 192kHz. Use the driver control panel (Windows)
or Audio MIDI Setup (Mac OS X) to set this.
M-Audio is a trademark of inMusic Brands, Inc., registered in the U.S. and other countries. Mac and
OS X are registered trademarks of Apple Inc., registered in the U.S. and other countries. Windows is
a registered trademark of Microsoft Corporation in the United States and other countries. All other
product names, company names, trademarks, or trade names are those of their respective owners.
Guía del usuario
Para más información acerca de este producto (requisitos de
sistema, información de compatibilidad, etc.), registro o soporte del
producto, visite m-audio.com. Para información sobre la seguridad
y la garantía, visite m-audio.com/warranty.
Contenido del paquete: Micro DAC 24/192, cable alargador USB,
cartuchera de transporte, guía del usuario
to download the necessary
Usuarios de Windows: Visitar
los drivers de Windows necesarios para Micro DAC 24/192.
6
3
4
2
1. Puerto USB: Inserte este conector en un puerto USB de su
ordenador (encendido). La conexión suministrará la corriente
necesaria al Micro DAC 24/192.
De ser necesario, utilice el cable alargador USB incluido para
que el Micro DAC 24/192 no obstruya ninguna otra conexión
adyacente en su ordenador.
2. Indicador de encendido: Esta luz se ilumina cuando el Micro
DAC 24/192 está encendido.
3. Salida para auriculares: Conecte auriculares estéreo estándar
de alta impedancia (32–150 Ω) de 3,5 mm (1/8 pulg.) a esta
salida analógica.
4. Salida para auriculares/digital: Utilice un cable óptico/digital de
3,5 mm (1/8 pulg.) para conectar esta salida a la entrada digital de
un dispositivo receptor o de reproducción. Como alternativa,
conecte auriculares estéreo estándar de baja impedancia (16–32 Ω)
de 3,5 mm (1/8 pulg.) a esta salida.
5. Volumen: Gire esta perilla para ajustar el volumen de las salida
para auriculares y la salida para auriculares/digital.
Nota: Como alternativa, ajuste el nivel de volumen en sus
auriculares, receptor o dispositivo de reproducción conectados,
o en la tarjeta de sonido de su ordenador.
6. Indicador de 192 kHz: Esta luz se ilumina cuando la tasa de
muestreo se ajusta a 192 kHz. Utilice el panel de control del
controlador (Windows) o Ajustes de audio MIDI (Mac OS X) para
ajustar esto.
(Español)
m-audio.com/drivers para descargar
5
1 6
3
4
2