Download
Share
Print this page
Draytek Vigor2962 Series Quick Start Manual
  1. Manuals
  2. Brands
  3. Draytek Manuals
  4. Network Router
  5. Vigor2962 Series
  6. Quick start manual

Draytek Vigor2962 Series Quick Start Manual

2.5g security vpn router
Hide thumbs Also See for Vigor2962 Series:

Advertisement

Quick Links

Download this manual
i

Advertisement

loading

Related Manuals for Draytek Vigor2962 Series

Summary of Contents for Draytek Vigor2962 Series

  • Page 2 Vigor2962 2.5G Security VPN Router Quick Start Guide Version:1.0_(official) Firmware Version: V3.9.3 (For future update, please visit DrayTek web site) Date: December 9, 2020...
  • Page 3 Intellectual Property Rights (IPR) Information © All rights reserved. This publication contains information that is protected Copyrights by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. The following trademarks are used in this document: Trademarks ...
  • Page 4 EU Declaration of Conformity We DrayTek Corp. , office at No.26, Fu Shing Road, HuKou County, Hsin-Chu Industry Park, Hsinchu 300, Taiwan , R.O.C., declare under our sole responsibility that the product  Product name: 2.5G Security VPN Router  Model number: Vigor2962 Series ...
  • Page 5 (1) This device may not cause harmful interference, and (2) This device may accept any interference received, including interference that may cause undesired operation. More update, please visit www.draytek.com. Company name ABP International Inc. Address 13988 Diplomat Drive Suite 180 Dallas TX 75234...

  • Page 6: Table Of Contents

    1. Introduction......................1 2. Panel Explanation....................2 3. Hardware Installation ................... 4 3.1 Connecting Device ........................4 3.2 Wall-Mounted Installation ......................5 4. Software Configuration ..................6 5. Customer Service ....................12...

  • Page 7: Introduction

    Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Vigor router Quick Start Guide RJ-45 Cable (Ethernet) Standard brackets The type of the power cord depends on the country that the router will be installed.

  • Page 8: Panel Explanation

    Status Explanation Blinking The router is powered on and running normally. The router is powered off. The fiber connection is established. Blinking The data is transmitting. No fiber connection is established or the system is hanged. The USB device is installed and ready. No USB device is installed.
  • Page 9 The Ethernet link is established on corresponding port with 1Gbps. Right The Ethernet link is established on corresponding port with less than 1Gbps. Interface Description The Factory Reset button is used to restore the default settings. Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds.

  • Page 10: Hardware Installation

    This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. Before starting to configure the router, you have to connect your devices correctly. Connect a modem to any WAN port of Vigor2962 with Ethernet cable (RJ-45) to access Internet.

  • Page 11: Wall-Mounted Installation

    The Vigor2962 Series can be mounted on the shelf or on the wall by using standard brackets shown below. Here we take mounted on the wall as an example. Choose a flat surface (on the wall) which is suitable for placing the router. Make the screw holes on the short side of the bracket aim at the screw holes on the router.

  • Page 12: Software Configuration

    To access Internet, please finish basic configuration after completing the hardware installation. 1. Make sure your PC connects to the router correctly. Note You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be the same subnet as the default IP address of Vigor router 192.168.1.1.
  • Page 13 3. Now, the Main Screen will pop up. 4. Open WAN>>Internet Access. Click Details Page of WAN1/WAN2. Here, we take WAN1 as an example. There are two access modes for you to configure. Choose PPPoE, Static or Dynamic IP according to the access mode offered by your ISP.
  • Page 14 Click Details Page of WAN1. When the following page appears, choose PPPoE. After clicking Enable and entering the Username/Password provided by your ISP, click OK to get the following page. To reboot the system, click OK again.
  • Page 15 Later, Vigor system will reboot. Please login Vigor router again. Then, you can enjoy surfing on the Internet.
  • Page 16 Click Details Page of WAN1. When the following page appears, choose Static or Dynamic IP. After clicking Enable, select Obtain an IP address automatically. Click OK to get the following page.
  • Page 17 To reboot the system, click OK again. Later, Vigor system will reboot. Please login Vigor router again. Then, you can enjoy surfing on the Internet.

  • Page 18: Customer Service

    Web registration is preferred. You can register your Vigor router via https://myvigor.draytek.com. Firmware & Tools Updates Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents.

This manual is also suitable for:

Vigor2962p