Table of Contents
Advertisement
Quick Links
Operation Manual
Compressor 24 ℓ
61957
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Table of Contents
Related Manuals for WilTec 24 L
Summary of Contents for WilTec 24 L
- Page 1 Operation Manual Compressor 24 ℓ 61957 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignific - antly.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 If the compressor produces strange noises or strong vibrations during operation or if it is de- • fective, the compressor must be stopped immediately. Contact a qualified technician for troubleshooting. © by WilTec Wildanger Technik GmbH Item 61957 Page 3 http://www.WilTec.de http://www.aoyue.eu...
- Page 4 Never use the compressor near water or in a humid environment. • Always wear protective glasses or eye protection. Never point the compressed air jet at your • own body or at other persons. © by WilTec Wildanger Technik GmbH Item 61957 Page 4 http://www.WilTec.de http://www.aoyue.eu 12 2020-1 http://www.teichtip.de...
- Page 5 Take the compressor out of its packaging and check that it is in good condition. The unit must not have suffered any transport damage. Do not operate the unit if it is damaged and contact the manufac- turer. © by WilTec Wildanger Technik GmbH Item 61957 Page 5 http://www.WilTec.de...
-
Page 6: Technical Data
A thin extension may result in a drop in voltage, loss of power and excessive heat generation. The single-phase compressor extension cable should have a cross-section appropriate to the • length of the cable. © by WilTec Wildanger Technik GmbH Item 61957 Page 6 http://www.WilTec.de http://www.aoyue.eu 12 2020-1 http://www.teichtip.de... -
Page 7: Operation
For compressors equipped with pressure reducers, a correct adjustment of the working pressure is required. This sets the desired pressure: Turn clock- wise (+) to increase the pressure and counter-clockwise (-) to decrease it. © by WilTec Wildanger Technik GmbH Item 61957 Page 7 http://www.WilTec.de... -
Page 8: Maintenance
The following causes can lead to an overload of the compressor and thus to the response of the over- load protection: Insufficient air supply • Leaking check valve • Defective compressor valves • Heavy conrod bearing • Mains voltage too high • © by WilTec Wildanger Technik GmbH Item 61957 Page 8 http://www.WilTec.de http://www.aoyue.eu 12 2020-1 http://www.teichtip.de... - Page 9 Children and animals must be kept away from the operating area of the machine. • If the power cable or plug is damaged, do not use the device! Contact an authorised techni - • cian. © by WilTec Wildanger Technik GmbH Item 61957 Page 9 http://www.WilTec.de http://www.aoyue.eu 12 2020-1 http://www.teichtip.de...
-
Page 10: Exploded View
Do not push any objects into the protective grilles and do not reach in with your hands as this • may cause injury to the user or damage to the device. Always disconnect the mains plug after using the compressor. • Exploded view © by WilTec Wildanger Technik GmbH Item 61957 Page 10 http://www.WilTec.de http://www.aoyue.eu 12 2020-1... -
Page 11: Disposal Regulations
All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste. -
Page 12: Eg-Konformitätserklärung
It has been tested with the following harmonised standards: Il a été testé à partir des normes harmonisées suivantes : EN 1012-1 :2010, EN 60204-1 :2006+A1 :2009 Bevollmächtigter für die Zusammenstellung der technischen Unterlagen: Bernd Wildanger, Geschäftsführer WilTec Wildanger Technik GmbH Königsbenden 12 52249 Eschweiler Deutschland Eschweiler, 13.