Table of Contents
Advertisement
For Fastext
The subject-heading for the information may have a particu-
lar colour or can be in a form located in a coloured box.
• Press an appropriate RED, GREEN, YELLOW or BLUE
button in order to reach the relevant page quickly.
For TOP text
TOP text mode of operation will be activated automatically
according to the transmission.
• If TOP text transmission is present, colour coded buttons
will appear in status row.
• If TOP text transmission is not present, status row will not
appear.
The subject-heading for information may be located in co-
loured box.
In Top mode the “P/CH+” or “-P/CH” commands will request
the next or previous page respectively. If TOP text transmis-
sion is not available, in case of operation of these com-
mands, wraparound occurs. For example page 100 appears
to be one greater than page 199.
To exit Teletext
79
• Press “
” button. The screen will switch to TV mode.
Connecting external equipment
Via the Euro connector
Your TV set has two euro connector sockets. If you wish to
connect external equipment (e.g. video recorder, decoder,
etc.) which have Euro connectors, to your TV, use the EXT.1
(EXT-1), EXT.2 (EXT-2) or EXT.3 (EXT-3)terminals.
If an external device is connected via Euro connector sock-
ets the TV will be switched to AV mode automatically.
RGB mode
If a piece of equipment outputs RGB signals use the EXT-1
Euro connector as this is RGB ready.
S-VHS EXT2 Mode
If the equipment connected to your TV set supports S-Video
(Y/C) output from Euroconnector, you can have a better pic-
ture quality by selecting S-VHS EXT2 mode and connecting
your equipment to the EXT.2 (S-VHS EXT2) terminal of TV.
See your equipment's booklet to check if your equipment
has such feature.
Via the ANT (aerial) socket
If your equipment does not have an Euroconnector or RCA
jacks, connect it to the TV with an aerial cable. For details,
see the manual provided with the equipment.
• To store the test signal that comes from the equipment,
see “Installation Menu” on page 13 and store it to the
programme number 0. You can watch images from that
equipment to select the programme number which you
stored the test signal.
Downloaded from:
http://www.usersmanualguide.com/
Via the RCA jacks
If you have an equipment (such as a Camcorder) which has
the RCA jacks, connect it to the FRONT-AV terminal with
the video and audio cables.
• If the equipment has the mono audio jack, connect it to the
AUDIO-L jack.
TV and Video Recoder (VCR)
• Connect the Video Recorder to the ANT (antenna input)
socket of the TV with the aerial cable.
• Connect the Video Recorder to the EXT.1, EXT.2 or EXT.3
terminal with the SCART cable, or connect it to the
FRONT-AV terminal with the audio and video cables.
• VCR is detected automatically.
NTSC Playback
Connect a NTSC video recorder to a terminal. Then press
(;7
“
” button to select the corresponding AV mode.
NTSC 3.58/4.43 system is detected automatically in AV
mode.
Copy Facility
You can output the video and audio signals which inputs
from TV, EXT.1 (EXT-1), EXT.3 (EXT-3), FRONT-AV or
SCREEN terminal to the video recorder connected to the
EXT.2 (EXT-2) terminal.
• To select the output source, see “EXT2 Output” on page
13.
To connect to S-VHS input
Connect your camera or camcorder at the front or back side
of your TV.
• Connect your equipment to the TV via S-VHS input and
audio inputs of FRONT-AV inputs by using S-VHS cables.
Connecting Headphones
Use the stereo headphone socket on the lower front side of
your TV, to connect headphones.
ENGLISH - 18 -
Advertisement
Table of Contents
