To Select A Subcode Page; Fastext; To Exit Teletext; Connecting External Equipment - Sharp 28LW-92H Operation Manual

To Select a Subcode Page

Subcode pages are subsections of long Teletext pages that
can only be displayed on the screen one section at a time.
• Select the required Teletext page.
• Press “ “ button.
• Select the required subcode page number by pressing four
digit buttons (e.g. 0001).
• If the selected subcode page is not displayed in a short
time, press “
the screen.
• Teletext page number will be displayed on the upper left
corner of the screen when the selected page is found.
• Press “ “button to display the selected Teletext page.

Fastext

Teletext mode will be selected according to transmission au-
tomatically.
Your TV supports the 7 page Teletext system. When the
page number of any of the 7 pages in memory is entered, the
system will not search for the requested page; instead it will
display the page automatically.
• Press “ ” button to move the Teletext screen forward one
page at a time.
• Press “ ” button to move the Teletext screen backward
one page at a time.
For Fastext
The subject-heading for the information may have a particular
colour or can be in a form located in a coloured box.
• Press an appropriate RED, GREEN, YELLOW or BLUE but-
ton in order to reach the relevant page quickly.

To exit Teletext

79
• Press “ ” button. The screen will switch to TV mode.

Connecting external equipment

Via the Euro connector

Your TV set has two euro connector sockets. If you wish to
connect external equipment (e.g. video recorder, decoder,
etc.) which have Euro connectors, to your TV, use the EXT.1
(EXT-1) or EXT.2 (EXT-2) terminals.
If an external device is connected via Euro connector sockets
the TV will be switched to AV mode automatically.

RGB mode

If a piece of equipment outputs RGB signals use the EXT-1
Euro connector as this is RGB ready.
Downloaded from: http://www.usersmanualguide.com/
“ button. TV programme will be displayed on

EXT-2S Mode

If the equipment connected to your TV set supports S-Video
(Y/C) output from Euroconnector, you can have a better pic-
ture quality by selecting EXT-2S mode and connecting your
equipment to the EXT.2 (EXT-2S) terminal of TV. See your
equipment's booklet to check if your equipment has such
feature.

Via the RCA jacks

If you have an equipment (such as a Camcorder) which has
the RCA jacks, connect it to the Front AV (F-AV) terminal
with the video and audio cables.
• If the equipment has the mono audio jack, connect it to the
AUDIO-L jack.

Via the ANT (aerial) socket

If your equipment does not have an Euroconnector or RCA
jacks, connect it to the TV with an aerial cable. For details,
see the manual provided with the equipment.
• To store the test signal that comes from the equipment,
see “INSTALL. Menu” on page 13 and store it to the pro-
gramme number 0. You can watch images from that equip-
ment to select the programme number which you stored the
test signal.

TV and Video Recoder (VCR)

• Connect the Video Recorder to the ANT (antenna input)
socket of the TV with the aerial cable.
• Connect the Video Recorder to the EXT.1 or EXT.2 terminal
with the SCART cable, or connect it to the Front AV (F-AV)
terminal with the audio and video cables.

NTSC Playback

Connect a NTSC video recorder to a terminal. Then press
(;7
“ ” button to select the corresponding AV mode.
NTSC 3.58/4.43 system is detected automatically in AV
mode.

Copy Facility

You can output the video and audio signals which inputs from
TV or EXT.1 (EXT-1) terminal to the video recorder connected
to the EXT.2 (EXT-2) terminal.
• To select the output source, see “Setting External Source
Output” on page 13.

Connecting Headphones

Use the stereo headphone socket of your TV, to connect
headphones.
- 17 -