Table of Contents
Advertisement
5.6 Performance
Item
６
Setting accuracy (
)
７
８
Display accuracy (
)(
Reproducibility of the
６
operating point (
)
Operating time
Reset time
Starting delay time
Influence of temperature
Influence of auxiliary
supply voltage variation
Operation period
Response time
Voltage input
Overload
Current input
capacity
Aux. supply
Insulation resistance
Power frequency
withstand voltage
Impulse withstand
voltage
Vibration
Shock
Power failure guarantee
Material of case
Color
Operating temperature
and humidity limits
Storage temperature limits
Mass
Accessories
６
Note(
) Input is DC60mV to less than 1V, DC±60mV to less than ±1V. ±0.2％ (％ of input span)
７
Note(
) Input is DC60mV to less than 1V, DC±60mV to less than ±1V. ±0.2％ (％ of input span) ±1digit.
８
Note(
) If the scaling span is 10,000 or more (5 digits excluding the decimal point), it is
±
span)
2 digits. If the scaling span is 10,000 or more and the input is less than 1V, it is
input span)
９
Note(
) When the average number is once. If the average number is 4, 8, 16, or 32, the operating time and
reset time will vary depending on the conditions.
10
Note(
) In case of 4-contact output, there is no insulation between AL1 and AL2 and between AL3 and AL4.
● About transition of a contact
In DC load switching, transition of a contact may start and a contact may not return by uneven connection.
A contact evaporates locally with arc heat, what carried out contact evaporation to + polarity → - polarity
carries out the adhesion deposition of this, and a single-sided convex opposite side serves as a concave.
〈Measure〉Be sure to use each relay within a rated load.
±0.1％ (％ of input span)
)
±0.1％ (％ of input span) ±1digit
±0.1％ (％ of input span)
±0.25 seconds of set value (Setting value 0 seconds = 0.5 ± 0.25 seconds)
Set value is contact delay time (
0.5 seconds or less (
±0.25 seconds of set value
0.2％ (For input span) / 23±10℃
0.1％ (For input span) / Within variation range
About 0.1 second
About 0.5 second
When a step change of 90％ to 110％ of the operating value setting is given (at CD = 0 seconds)
2 times 10 seconds and 1.5 times continuation of rated voltage.
10 times 5 seconds and 1.5 times continuation of rated current.
1.5 times 10 seconds of rated voltage. Variable range upper limit continuous.
Between electric circuit and case.
Between input, output terminals and auxiliary supply
terminals.
Between input terminals and output terminals.
2 contacts
Between
output
3 contacts
terminals
4 contacts
Between electric circuit and case.
Between input, output terminals and auxiliary supply
terminals.
Between input terminals and output terminals.
2 contacts
Between
output
3 contacts
terminals
4 contacts
Between electric circuit and case.
Vibration of vibration frequency 16.7Hz，Double amplitude 1mm.
In the direction of X Y Z for each 10 minutes. There must not be malfunction.
2
Error：98m/s
, X, Y, Z direction for each 3 times.
2
Duration：294m/s
, X, Y, Z direction for each 3 times.
Each set value is data-saved by non-volatilized memory.
Case：Flame resisting ABS resin , Name plate：Polyester film
Munsell N1.5 (Black)
-10 to +55℃ , 5 to 90％RH (Non condensing)
-25 to +70℃
180g
Approx.
Unit symbol sheet，Instruction manual
±
2 digits.
Specification
９
)
９
)
Between AL1 and AL2
Between AL1 and AL2 and AL3
Between AL1・AL2 and AL3・AL4 (
Between AL1 and AL2
Between AL1 and AL2
Between AL1・AL2 and AL3
Between AL1・AL2 and AL3・AL4 (
5kV 1.2/50μs. Both positive and negative polarity
for 3 times each. There must not be malfunction.
18
FSDLC-220-047
Above 50MΩ at DC500V
10
)
AC2000V (50/60Hz) 1 minute.
There must not be malfunction.
AC1000V (50/60Hz) 1 minute.
There must not be malfunction.
AC2000V (50/60Hz) 1 minute.
10
There must not be malfunction.
)
±
％
0.1
(for input
±
0.2
９
(
)
％
(for
Advertisement
Table of Contents
