Setting Value - Daiichi Electronics FINE Series Instruction Manual

5.5 Setting value

№ Contents
1 Unit display
2 Minimum value scaling
3 Maximum value scaling
4 Output mode
5 Operation value
AL1
6 Dead band
7 Excitation mode
8 Contact delay time (CD)
9 Output mode
10 Operation value
AL2
11 Dead band
12 Excitation mode
13 Contact delay time (CD)
14 Output mode
15 Operation value
AL3
16 Dead band
17 Excitation mode
18 Contact delay time (CD)
19 Output mode
20 Operation value
AL4
21 Dead band
22 Excitation mode
23 Contact delay time (CD)
24 Starting delay time (SD)
25 Bias point calibration
26 Span point calibration
27 Average number
28 Pre-alarm
< Notes of setting >
・The decimal point position change of scaling is made by the minimum value scaling.
If the decimal point position is changed, the decimal point position of maximum value scaling and operation
values 1 to 4 will also change. If the decimal point position is changed, please be sure to check the set
value of a maximum value scaling and an operation value.
・When changing the scaling, set the operation values 1 to 4 within the measurement display range (see below).
Even if the output mode is set to OFF, keep it within the measurement display range.
・An operation value can be set up in -25 to +125％ of the measurement display range (minimum value scaling
to maximum value scaling).
(Example) Input 4 to 20mA,
Operation value -25.0,
Output mode is "Low" setting.
・After setting change, in case a set value combination error occurs, it becomes a setting error display.
Please push the
Default setting value
Mark
2 contact
outputs
UNIT
MIN
MAX
ALMD1 High
COMP1 70.0
D.B.1
EXMD1
C.D.1
ALMD2 Low
COMP2 30.0
D.B.2
EXMD2
C.D.2
ALMD3 －
COMP3 －
D.B.3 －
EXMD3 －
C.D.3 －
ALMD4
COMP4
D.B.4
EXMD4
C.D.4
S.D.
CBIAS
CSPAN
AVE
PREAL
125％
100％
-25％
key and set up the right set value (in set value change mode).
3 contact 4 contact
outputs outputs
％
0.0
100.0
High High
80.0 80.0
3.0
0N
0
High High
70.0 70.0
3.0
0N
0
Low Low
30.0 30.0
3.0
ON
0
－ Low
－ 20.0
－ 3.0
－ ON
－ 0
5
0.00
0.00
1
OFF
24mA
20mA
50％ 12mA
Becomes the L detected at the input 0mA,
can also be used as a disconnection
0％ 4mA
detection.
0mA
17
Setting range
３
％ ， m， ℃， m /h， ppm， pH， TPm， ×10kg，
Ω，kW，No unit
-9999 to 9999 -9.99 to 99.99
-99.9 to 999.9 0.000 to 9.999
High：H operation，Low：L operation，
OFF ：With no operation
Measurement display range -25 to
+125％ (Real scale)
0.5 to 50.0％
ON：Excitation，OFF：Non-excitation
0 to 180s
High：H operation，Low：L operation，
OFF ：With no operation
Measurement display range -25 to
+125％ (Real scale)
0.5 to 50.0％
ON：Excitation，OFF：Non-excitation
0 to 180s
High：H operation，Low：L operation，
OFF ：With no operation
Measurement display range -25 to
+125％ (Real scale)
0.5 to 50.0％
ON：Excitation，OFF：Non-excitation
0 to 180s
High：H operation，Low：L operation，
OFF ：With no operation
Measurement display range -25 to
+125％ (Real scale)
0.5 to 50.0％
ON：Excitation，OFF：Non-excitation
0 to 180s
1 to 180s
-9.99 to 9.99％ (％ of input span)
-9.99 to 9.99％ (％ of input span)
1，4，8，16，32
ON：Pre-alarm ON, OFF：Pre-alarm OFF
FSDLC-220-047