Advertisement
METER INSTALLATION
A
Install with the adjustable stand
Fasten using the
1. Installing the adjustable stand
double-sided tape.
Place the stand's holder band around the back of the meter.
①
Note: If you cannot get the band around the meter, loosen
( O n t o p o f t h e
the hexagonal bolt and expand the band.
s t e e r i n g c o l u m n
After getting the band in place, tighten the hexagonal bolt to
②
cover or dashboard)
secure the band.
Can be mounted in various
places
Mount almost anywhere using the
double-sided tape. After mounting it
is possible to for easy-reading.
SETTINGS
PREPARATION
Please check the number of cylinders and cycles for the model car being used.
A
Cylinder Number Setting
SETTING
Set the cylinder number for the car being used.
The number of cylinders is set by the shift lamp pattern.
OFF
Press the
1
switch
Press the switch during the key
switch OFF (meter light off)
2
ENGINE
START
While holding the switch, start
the engine within 5 seconds.
4
5
6
-cylinder
Turn
Patterns for cylinder settings display
Number of
Shift lamp
Car models
cylinders
1
NISSAN (FAIRLADY Z Z33)・MAZDA (ATENZA and others)
2
MAZDA (RX-8)・SUBARU (early type of PLEO and others)
Note: For one and two cylinder engines,
set the signal level switch to two.
3
Three-cylinder
4
Four-cylinder, Rotary engine (RX-7)
5
Five-cylinder
6
Six-cylinder
8
Eight-cylinder
A
Some models of NISSAN
Special
Reference: If the engine is a two cycle engine, multiply the number of cylinder by two.
(e.g., For a two-cycle three-cylinder engine the setting would be six.)
With no operation
6
for 2 seconds
7
OPENING DEMO
B
Peak reading display and re-set
SETTING
1
Press the
switch once
While the tachometer is being
displayed, press the switch once.
2
Peak reading
display
3
Press the switch
for 2 seconds
Pressing the switch will re-set the
peak reading.
Holder band
Hexagonal bolt
with washer
On the dashboard
On the steering
column cover
3
OPENING DEMO
4
Cylinder display
(The factory default setting is for a
four-cylinder engine)
Press the
5
switch once
Press the switch to change the
pattern and set to the proper one.
8
A
1
2
Special
= On
= Blink
⇒ See
SETTING E
for details.
The needle will show the
8
set shift point
The lamps blink red
9
Tachometer display
Press
The needle will show "0"
4
All shift lamps will light
5
Tachometer display
Double-sided tape
(included)
Clean to remove
oil & dust
2. Installing to the car
Bend the stand to securely fit the place of installation.
①
Clean the surface; removing all oil or dust.
②
③
Fasten using the double-sided tape.
Note: Please be sure about where you wish to install the
meter, as it is not advisable to reuse double-sided tape.
15
30
Meter dimensions
(unit; mm)
ø65
ø60
C
Shift Point Setting
SETTING
Make RPM setting for turning on the shift lamp. (setting range : 3000–9000 rpm)
1
While the tachometer is being
displayed, press the switch for long.
The needle will show the
2
set shift point
The lamps blink red
3
Press the
switch
3
While holding down the switch,
change the RPM setting
= Off
D
Shift lamp brightness setting
SETTING
Make setting to change the shift lamp brightness.
1
While the tachometer is being
displayed, press the switch for long.
After 1.5 seconds the shift
2
point will be shown and after 5
seconds
All lamps will light
3
Press the
switch
E
Switching the signal level
SETTING
Changes are only necessary for those car models listed below.
NISSAN (FAIRLADY Z Z33)/ MAZDA (after 2002)/
MITSUBISHI (COLT and others)/SUBARU (early type of PLEO and others)
Note: See the "Wiring Chart" for details.
During meter light Off
1
ON
Key ON
(engine not running)
2
Press the switch
for 5 seconds
5
Press the
switch
Set the signal detection level by
pressing the switch to change the
needle position to the correct setting.
6
With no operation
for 2 seconds
Install in an easy-to-view location.
B
Installation with the
cushion tape
Hexagonal
bolt
④
After deciding the
position and angle of
t h e m e t e r f a c e ,
Wrap the cushion tape around the
fasten the hexago-
base of the meter and forcibly insert
n a l b o l t s o n b o t h
into the 60 mm hole in the panel.
sides to secure.
If you wish to open holes to fasten
the unit to the pillar or column
cover, please purchase and use
the separately sold pillar holder.
PH-60
Pillar holder for ø60
After finishing the installation, make various settings.
Press for 1.5 seconds
4
Press the switch
for 1.5 seconds
5
Each pressing of the switch will
raise, the setting 200 rpm; at 9000
rpm it will return to 3000 rpm.
Note: By continually pressing down on the switch the
needle will move to 9000 rpm.
Press for 5 seconds
4
Press the switch
for 5 seconds
5
All shift lamps
will light
Each pressing will change
Bright
Dark
the brightness.
2 steps
Press for 5 seconds
3
The needle will show "1"or"2"
4
The lamps blink red
1
= If the generic car
3
0
1 1
2
7
Cushion
Panel
tape
A pillar
Screw
Pillar
hole
holder
With no operation
for 2 seconds
Tachometer display
With no operation
for 2 seconds
Tachometer display
OPENING DEMO
2
= If the level is small
3
0
2 2
1
Lamp Off
3
Advertisement
