1. Veiligheidsmaatregelen Informatie Voor waarborgen van veilig gebruik en service van de tester volg deze instructies. Nalaten van bestuderen van de waarschuwingen kan leiden tot ernstige verwondingen of de dood. - Vermijdt het werken alleen, zodat assis- tentie verleend kan worden. Als de veiligheid van degene die het instrument gebruikt, niet meer gegarandeerd kan worden, dan dient het instrument buiten werking gesteld te...
2. Symbolen en Kenmerken Op het instrument en in deze gebruikers- handleiding gebruikte symbolen. Voorzichtig! Gevaarlijke spanningen Raadpleeg de handleiding + or - + DC of –DC meting Dubbel geïsoleerd Batterij Aarde ± AC meting Conform EU standaard Hoge Spanning Detectie Kenmerken...
3. AC/DC V spanningsmetingen AC V DC V EazyVolt : De veiligheids LED zal een indicatie geven bij Spanningen >50V AC en 120V DC. EazyVolt plus: Boven 50V AC / 120V DC zal de Hooge Spanning indicatie oplichten. Let erop dat het geluidssignaal van de tester waarneembaar is wanneer wordt getest in een luidruchtige omgeving.
5. Weerstandsmetingen Allen on Eazy Volt De weerstand is alleen mogelijk indien de batterijen geïnstalleerd én in goede conditie zijn. 6. Éénpolige fase detectie Éenpolige fase Stevig vasthouden →...
Eenpolige Fase detectie is alleen mogelijk indien de batterijen geïnstalleerd én in goede conditie zijn. Eénpolige fase detectie is niet altijd geschikt voor het testen van aanwezige spanning. Hiervoor is de tweepolige test nodig. De weergave functie kan beïnvloed worden tijdens fase testen om externe leidingen vast te stellen (bv.
Page 10
Links draaiveld Stevig vasthouden → Het testen van fase volgorde richting is mogelijk vanaf 100V AC voltage (fase-fase) op voorwaarde dat de nul geaard is. Bij het contact maken van beide meetpunten naar 2 fases van de 3 fase voeding, verbonden met rechtsomdraaiend draaiveld, verschijnt het “B“symbool in het LCD scherm.
Waarschuwing: Let erop dat tijdens het testen van de draaiveldrichting, de meetpunten goed contact maken met 2 van de 3 fases. Voor exacte vaststelling van een rechtsdraaiende draaiveldrichting is het noodzakelijk een negatief draaiveld te testen na verandering van fases. De indicaties “B“ of “ C“ kunnen beïnvloed worden door ongunstige licht omstandigheden, door beschermende kleding of geïsoleerde locatie.
Om het aanspreken van een aardlekschakelaar te voorkomen moet een test uitgevoerd worden tussen fase en nul gedurende ca. 5 seconden. Gelijk erna kan spanning tussen fase en aarde worden gemeten zonder dat de aardlekschakelaar aanspreekt. 9. Meetpuntverlichting...
10. Frequentie Metingen Allen Eazy Volt + 11. Zelf- Tests Eazy Volt : Autotest door de gele knop te bedienen. Eazy Volt Plus : Autotest door de probes contact met elkaar te laten maken. Wanneer het instrument niet goed werkt, gebruik het dan niet, maar stuur het naar onze service afdeling voor reparatie.
12. Vervangen batterij Indien bij kortsluiten van de meetpennen geen geluidssignaal hoorbaar is (EazyVolt) of het “<“symbool verschijnt (EazyVolt+): - De EazyVolt / EazyVolt+ compleet los nemen van het testobject. - Met een passende schroevendraaier/munt (De metalen deksel heeft een doorsnede van 8mm en een dikte van 2mm) de schroef los draaien en het batterijvak openen.
14. Reinigen Vóór het reinigen, eerst het instrument verwijderen van alle spanningscircuits. Reinig de behuizing periodiek met een licht vochtige doek en (mild) schoonmaak-middel. Gebruik hiervoor nooit een agressief schoonmaak- of oplosmiddel. Na reiniging het instrument niet gebruiken voordat het weer goed droog is. 15.
De gebouwinstallatie De bron van de laag- CAT IV spanningsinstallatie 18. Garantie Nieaf-Smitt producten ondergaan strenge kwaliteitscontroles. Mochten er desondanks tijdens normaal gebruik, gebreken ontstaan, dan verlenen wij een garantie van 24 maanden. Productie- of materiaalfouten worden kosteloos door ons verholpen, indien het instrument zonder invloed van buitenaf aan ons wordt retour gestuurd.
Page 20
Eazy Volt Eazy Volt Plus Voltage Tester Instruction Manual Eazy Volt Eazy Volt Plus...
Page 21
TABLE OF CONTENTS Page 1. Safety 2. Symbols and Features 3. AC/DC V Measurements 4. Continuity / Diode Tests 5. Resistance Measurements 6. Single-Pole Phase Tests 7. Phase Rotation Tests 8. RCD Voltage Tests 9. Illumination 10. Frequency Teats 11. Auto Test 12.
1. Safety Safety Information To ensure safe operation and service of the Tester, follow these instructions. Failure to observe warnings can result in severe injury or death. - Avoid working alone so assistance can rendered. If the operators safety can not be guaranteed, the Tester must be removed from service and protected against use.
– Continuity – Resistance (Eazy Volt Plus) – Single pole phase test – Phase rotation of a three-phase mains – Frequency test (Eazy Volt Plus) – Auto test – Probe tip torch – Drop proof 1 meter – IP 65 Protection –...
3. AC/DC V Measurements AC V DC V Eazy Volt : The safety LED can report a dangerous voltage> 50 V AC and 120 V DC Eazy Volt Plus : The safety indicator can report a dangerous voltage > 50 V AC and 120 V DC.
5. Resistance Measurements Only on Eazy Volt The Resistance test is only possible when batteries are installed and in good condition. 6. Single-Pole Phase Test Single-Pole Phase Firmly →...
The single-pole phase test is only possible when batteries are installed and in good condition. The single-pole phase test is not always appropriate for testing whether a circuit is not live. For this purpose, the bipolar test is required.
Page 29
Left rotary field Firmly → Testing of phase-sequence direction is possible from 100V AC voltage (phase to phase) provided the neutral is earthed. On making contact with both test electrodes (probe tips) to two phases of the three-phase power supply which are connected in clock- wise rotation, a “B”...
Attention : Please ensure that the test electrodes (probe tips) make good contact with two phases of a three-phase mains while testing the phase rotation. For absolute determination of a clock- wise phase rotation it is necessary to make a negative phase rotation test after changing the phases.
To avoid RCD tripping, a test has to be carried out between L and N during approx. 5sec. Immediately afterwards, voltage testing between L and PE can be carried out without RCD tripping. 9. Illumination Probe tip torch...
10. Frequency Tests Only on Eazy Volt plus 11. Auto Tests Eazy Volt : auto-test by pressing the yellow button Eazy Volt Plus : auto-test by shorting the probes If the instrument shows failure, please don’t use it and send it to our service depart-...
12. Battery Replacement If no signal sound is audible (Eazy Volt) when short circuiting the test probes, if the symbol “<” is displayed (Eazy Volt Plus) - Completely disconnect from the measure- ment circuit. - Unscrew the screw by a cross screw driver, then open the battery cover.
14. Cleaning Prior to cleaning, remove the instruments from all measurement circuits. If the instruments are dirty after daily usage, it is advisable to clean them by using a damp cloth and a mild household detergent. Never use acid detergents or dissolvent for clean- ing.
17. Specification Eazy The Instruments Eazy Volt Plus Volt Voltage range 12….750V AC/DC ± 12,24,50,120,230,400, LED/Bargraph resolution 750V 12V…750V LCD voltage range AC/DC LCD resolution AC ±(1.3%+5d) Accuracy DC ±(1.0%+2d) Voltage detection Automatic AC 50V Acoustic signal sound DC 120V...
Page 36
Eazy The Instruments Eazy Volt Plus Volt Continuity Test Threshold < 200KΩ < 200Ω Diode Test 0.1~1.0V Resolution 0.1V Overvoltage protection 1000V AC/DC Rotary Field Indication Voltage range (LEDs) 100…750V Frequency range 50…60Hz Measurement Double-pole and firmly principle hold the grip (L2) 2 x 1.5V IEC LR03 AAA...
Overvoltage category CAT III 1000V, Overvoltage class CAT IV 600V CAT. Application field The circuits not connected CAT I to mains. The circuits directly CAT II connected to Low-voltage Installation. CAT III The building installation The source of the Low – CAT IV voltage installation.