Advertisement
4.2.
general jacking.
WarNiNg! Before lifting ensure safety
‰
instructions are read and understood.
4.2.1.
Position the jack saddle under the vehicle
manufacturer's recommended lifting point
along sill edge.
4.3.
jacking the vehicle.
4.3.1.
close the release valve. Attach handle
extension
4.3.2.
commence pumping handle up and down
using maximum strokes until the jack saddle
reaches the vehicle manufactures jacking
point. check the jacking point is centrally
located on the saddle and raise the vehicle.
4.3.3.
should the jack become overloaded, a safety
excess pressure valve will open, and stop
the vehicle from lifting.
WarNiNg! the jack is a lifting device only
‰
and must not be used to support the load.
use correctly rated axle stands to support
the load.
4.4.
lowering the vehicle.
4.4.1.
if using axle stands, raise the jack high
enough for the stands to be easily removed. then attach handle extension to release valve and turn handle anticlockwise very slowly
to open the valve.
4.4.2.
the lowering speed is controlled by the amount you turn the handle. lower carefully, avoid any sudden changes in descent rate which
would shock load the hydraulic system.
WarNiNg! ensure there are no persons or obstacles beneath the vehicle, or in the path of its descent.
‰
5. MaiNTeNaNce
5.1.
When not in use, the ram should be in its lowest position to minimise corrosion. remove handle extension and store in case.
5.2.
Keep the jack clean and lubricate all moving parts with oil on a regular basis.
5.3.
Before each use check for broken, cracked, bent, or loose parts, or any visible damage to ram, pump, saddle, frame and all parts
including nuts, bolts, pins and other fasteners. if any suspect item is found remove jack from service and take necessary action to
remedy the problem.
do NoT use the jack if believed to have been subjected to abnormal load or shock load.
8
5.4.
Periodically check the pump piston and the ram for signs of corrosion. clean exposed areas with a clean oiled cloth.
5.5.
After one year the oil should be replaced in order to extend the life of the jack. use hydraulic jack oil only.
WarNiNg! only competent personnel should attempt hydraulic maintenance or repair.
‰
5.6.
to check the oil level, fully lower the jack. remove filler plug fig.1. the correct level is the bottom of the hole. if oil level is low, fill as
required. Pump jack 5 or 6 times to expel air. Pump jack up to full height before refitting plug.
do NoT touch the safety overload valve fig.1.
8
NoTe: use a good quality jack oil, such as seAleY HYdrAulic JAcK oil.
WarNiNg: do NoT use brake fluid, or any fluid other than hydraulic jack oil as this may cause serious damage to the jack and will
‰
invalidate the warranty.
iMporTaNT: no resPonsiBilitY is AccePted for incorrect use of Product.
9
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the uK.
do NoT reTurN jacks To us. Please telephone us on 01284 757500 to obtain the address and 'phone number of your local
8
agent. if jack is under guarantee contact your local sealey dealer.
5.7.
de-commissioning the jack
should the jack become completely unserviceable and require disposal, draw off the oil into an approved container and dispose of
the jack and the oil according to local regulations.
environmental protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMporTaNT: no liability is accepted for incorrect use of this product.
WarraNTy: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar
Original Language Version
01284 757500
01284 703534
HsJ07 | issue 1 04/11/16
www.sealey.co.uk
sales@sealey.co.uk
Advertisement
