Table of Contents
Advertisement
Quick Links
Features
• Photoelectric Smoke Alarm
• Removable smoke chamber for
easy maintenance
• Automatic calibration and
self test
• Fully supervised for low battery
and malfunction
• Manual test button helps to
verify battery status and alarm
operation
• Built-in 85dB local sounder and
flashing red LED light will
indicate prescence of smoke
WARRANTY
This product is sold subject to our standard
warranty against defects in workmanship
for a period of two years. Please note: In
positions where the Deltabell WE casing is
subjected to high levels of U.V. sunlight,
there may be risk of case colour fading, this
is not covered by the warranty. In the
interest of continuing improvement of
quality, customer care and design, Pyronix
Ltd reserve the right to amend specifica-
tions without giving prior notice.
Customer support line (UK only): +44(0)845 6434 999 (local rate)
SMOKE-WE
Smoke detector
Customer support:
Or telephone: +44(0)1709 535225
Hours: Mon to Fri, 8:00am till 6:30pm
Email: customer.support@pyronix.com
Website: www.pyronix.com
Dimensions
120mm
Width:
120mm
Height:
120mm
Depth:
5.3mm
RINS1367-1
Advertisement
Table of Contents
Summary of Contents for Pyronix ENFORCER SMOKE-WE
- Page 1 In the interest of continuing improvement of Width: 120mm quality, customer care and design, Pyronix Height: 120mm Ltd reserve the right to amend specifica- Depth: 5.3mm...
- Page 3 Introduction The Enforcer wireless photoelectric smoke alarm is designed to sense smoke that comes into the alarm chamber. It does not sense gas, heat, or flame. This smoke alarm is designed to give early warning of developing fires by giving off the alarm sounds from its built-in alarm piezo. It can provide precious time for you and your family to escape before a fire spreads.
- Page 4 Wireless signal strength test Learn button Figure 2 Printed Circuit Board The LED gives a visual indication of the wireless signal strength: • Green indicates good signal strength and is a good location to install. • Red indicates poor signal strength and the device should not be installed in that position. •...
- Page 5 • Install a smoke alarm inside every room where one sleeps with the door partly or completely closed, since smoke could be blocked by the closed door and a hallway alarm may not wake up the sleeper if the door is closed. •...
- Page 6 alarms. Install smoke alarms at least 3 metres away from bathrooms. • In very cold or very hot areas, including unheated buildings or outdoor rooms. If the temperature goes above or below the operating range of the smoke alarm, it will not work properly.
- Page 7 Please follow these steps to install your smoke alarm: 1. At the place where you are going to install your smoke alarm, draw a horizontal line 15cm (6 inches) long. 2. Remove the mounting bracket from your unit by rotating it anticlockwise. 3.
-
Page 8: Product Specification
Product specification Battery: CR123A -3V, battery life greater than 2 years Sensitivity: Meet with both UL217 and EN14604 standard 1.8%~3.1% Sound level: 85dB/3m Warning sound pattern: meet with UL/ULC standard (Pre-setting at UL standard) Alarm Audibility: 85dB/3m Red alarm LED indication Operation Temperature: -10°C~50°C Relative Humidity : 10~95% Size: 120mm diameter x 5.3mm depth... -
Page 9: Battery Installation
IMPORTANT: The smoke alarm will transmit the alarm signal to the Enforcer control panel, enter your code or present your tag to silence the alarm. If the smoke alarm beeps once with yellow LED flashing three times in a minute, it indicates the smoke alarm is not working properly , it needs to be repaired or serviced. -
Page 10: Limitations Of Smoke Alarms
Taking care of your smoke alarm Your smoke alarm is designed to be as maintenance free as possible. To keep your smoke alarm in good working condition, you must test the unit weekly, as referring to section “TESTING YOUR SMOKE ALARM”. Regular Maintenance: •...