Bosch Professional GFZ 16-35 AC Original Instructions Manual page 13

Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Saw blade body
(2) Auxiliary handle (insulated gripping surface)
(3) Stroke rate preselection thumbwheel
(4) Lock-off button for on/off switch
(5) On/off switch
(6) Handle (insulated gripping surface)
A)
(7) Extraction hose
(8) Extraction outlet
(9) SDS button for saw blade release
(10) Cams for extraction outlet
(11) Saw blade guard
A)
(12) Saw blade
(13) Knurled screw for auxiliary handle
(14) Spacer tube for auxiliary handle
(15) Knurled nut for auxiliary handle
(16) Screw for auxiliary handle
(17) Saw blade driving pin
(18) Engaging pin for saw blade
(19) Saw blade guide
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Reciprocating Saw
Article number
Rated power input
No-load stroke rate n
0
Stroke
Blade body length
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/vibration information
Noise emission values determined according to
EN 62841-2-11.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 92 dB(A); sound power level
103 dB(A). Uncertainty K=5 dB.
Wear hearing protection
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-11:
Bosch Power Tools
Cutting boards with saw blade TF 350 M:
a
Cutting wooden beams with saw blade TF 350 M:
a
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
u
u
GFZ 16-35 AC
Auxiliary handle
0 601 637 7..
Fitting the auxiliary handle (see figures A−C)
W 1600
Slide the spacer tube (14) into the opening on the housing
−1 and tighten it with the knurled screw (13).
min 850−2600
Extend the auxiliary handle (2) and place it over both ends of
mm 50
the spacer tube (14).
mm 350
Insert the screw (16) into the auxiliary handle and spacer
kg 5.8
tube and tighten it with the knurled nut (15).
Repositioning the auxiliary handle (see figure D)
/Ⅱ
You can reposition the auxiliary handle (2) to any angle for a
safe work posture that minimises fatigue.
Loosen the knurled nut (15) and adjust the auxiliary
handle (2) to the required position. Retighten the knurled
nut.
Adjusting the auxiliary handle (see figure E)
When sawing close to edges, the auxiliary handle (2) can be
moved to the side.
Loosen the knurled screw (13) and reposition the auxiliary
handle (2) with the spacer tube (14) into the required posi-
tion. Retighten the knurled screw.
2 2
=5 m/s , K=1.5 m/s ,
h,B
2 2
=5 m/s , K=1.5 m/s .
h,WB
Pull the plug out of the socket before carrying out any
work on the power tool.
For all work on the power tool, attach the saw blade
guard to the saw blades.
English | 13
1 609 92A 4YJ | (13.06.2019)