Mitsubishi Electric WB-PA5 Installation Manual

MANUFACTURED FOR:
MITSUBISHI ELECTRIC US, INC.
Wind Baffle
WB-PA5
for use with:
PUY/Z-A24/30/36NHA4/NHA6; PUY/Z-A42NHA4/NHA5
PUZ-HA30/36NA4; PUMY-P36/48NHMU; PUY/Z-A24/A30NHA7
Outdoor Units
Installation Instructions
Installation Instructions
Wind Baffle Part # WB-PA2
INSTALLATION MANUAL
For safe and correct use, please read this installation manual thoroughly before installing the advanced wind baffles.
WARNING! MOVING PARTS. INCORRECT HANDLING COULD LEAD TO DEATH OR INJURY!
Wind Baffle Part # WB-PA2
WARNING! MOVING PARTS. INCORRECT HANDLING COULD LEAD TO DEATH OR INJURY!
WARNING! MOVING PARTS. INCORRECT HANDLING COULD LEAD TO DEATH OR INJURY!
IMPORTANT! Outdoor Unit should be installed with back coil surface facing a wall or oriented
so the wind does NOT blow directly on to the back coil surface. Do not install this product
where there is any obstacle at either side or above the outdoor unit. If the discharge air is
IMPORTANT! Outdoor Unit should be installed with back coil surface facing a wall or oriented so the wind
IMPORTANT! Outdoor Unit should be installed with back coil surface facing a wall or oriented
does NOT blow directly on to the back coil surface. Do not install this product where there is any obstacle at
so the wind does NOT blow directly on to the back coil surface. Do not install this product
either side or above the outdoor unit. If the discharge air is obstructed the air may be short cycled.
Steps:
where there is any obstacle at either side or above the outdoor unit. If the discharge air is
1. Remove 5 screws holding fan guard in place.
STEPS:
2. Slide fan guard into wind baffle lining up the stopper tabs.
Steps:
1. Remove four(4) or five(5) screws holding fan guard in place.
3. Position wind baffle/fan guard and line up with pre-punched holes.
1. Remove 5 screws holding fan guard in place.
2. Slide fan guard into wind baffle lining up the stopper tabs.
4. Install all 5 screws and tighten securely. Repeat with all baffles.
2. Slide fan guard into wind baffle lining up the stopper tabs.
3. Position wind baffle/fan guard and line up with pre-punched holes.
5. Attach the safety string to the lower left inside of baffle using the pre-punched hole
3. Position wind baffle/fan guard and line up with pre-punched holes.
4. Install all four(4) or five(5) screws and tighten securely. Repeat with all baffles.
and the provided 10-24 screw and nylon lock nut. Attach the other end to the closest
4. Install all 5 screws and tighten securely. Repeat with all baffles.
existing cabinet screw. Repeat with all baffles.
5. Attach the safety string to the lower left inside of baffle using the pre-punched hole
ENSURE BAFFLE OUTLETS WILL NOT BE BLOCKED OR OBSTRUCTED !
and the provided 10-24 screw and nylon lock nut. Attach the other end to the closest
Note: When two fan outdoor unit is used, two wind baffles are required.
existing cabinet screw. Repeat with all baffles.
Install lower baffle first for easier installation.
ENSURE BAFFLE OUTLETS WILL NOT BE BLOCKED OR OBSTRUCTED !
Note: When two fan outdoor unit is used, two wind baffles are required.
Note: When two fan outdoor unit is used, two wind baffles are required.
Install lower baffle first for easier installation.
Install lower baffle first for easier installation.
STEP 1
STEP 1
STEP 3
© 2017 Mitsubishi Electric US, Inc.
Sep 2015
obstructed the air may be short cycled.
obstructed the air may be short cycled.
ENSURE BAFFLE OUTLETS WILL NOT BE BLOCKED OR OBSTRUCTED !
Manufactured for Mitsubishi Electric US, Inc.
© 2012 Mitsubishi Electric US, Inc.
FOR INSTALLER
stopper
STEP 2
STEP 2
STEP 4
Specifications are subject to change without notice.
English
stopper or wire tab