twin busch TW F-50 T Instruction & Maintenance Manual
  1. Manuals
  2. Brands
  3. twin busch Manuals
  4. Wheel Balancers
  5. TW F-50 T
  6. Instruction & maintenance manual

twin busch TW F-50 T Instruction & Maintenance Manual

Truck wheel balancer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TW F-50 T and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for twin busch TW F-50 T

Summary of Contents for twin busch TW F-50 T

  • Page 2 Technical changes for purposes of a technical advancement as well as deviation in colour, errors and printing mistakes are reserved.

  • Page 3: Table Of Contents

    Index 1. Summary of the balancing machine ..............4 A. Brief introduction of appearance ..............4 B. Performance and characteristics ..............5 C. Technical data table ..................6 2. Accessories accompanying machines............6 - 7 3. Use of balancing machine ..................8 A.

  • Page 4: Summary Of The Balancing Machine

    1. Summary of the balancing machine A. Brief introduction of appearance 1. Gauge 2. ON/OFF switch 3. Centering cones 4. Storage compartments 5. Display 6. Wheel cover 7. Quick release nut 8. Main shaft 9. Joystick (for pneumatic lift) 10. Wheel slide 11.

  • Page 5: Performance And Characteristics

    B. Performance and characteristics ● This machine adopts imported large-scale integrated circuit to make up the microcomputer system with high intelligence and high stability. This machine is equipped with the counterweight optimization procedure. ● Main shaft of balancing adopts imported bearing for transmission, it is processed accurately. It is wear-resisting and low noise.

  • Page 6: Technical Data Table

    C. Technical data table Garage, transportation company ,Department motorcade, Scope of application The professional service station of tyre Width of steel rim 1,5”～20” Diameter of steel rim 13”～24” Maximum weight of wheel 150kg Measurement time 8 seconds each time Power supply 400 V <70dB Noise level...
  • Page 7 Delivery contents Please check all parts of delivery for completeness and damages in transit. If something is missing or damaged, please contact the supplier directly. Supplied accessories: Overview Diameter of cones Diameter (inside) Height Weight 310 mm 150 mm 70 mm 8.5 kg 225 mm 150 mm...

  • Page 8: Use Of Balancing Machine

    3. Use of balancing machine A. Attention before use When moving the balancing machine you should only lift the machine chassis and never lift the machine by the shaft. The Balancing machine and pneumatic lifting device must placed on level ground (should be fixed with expansion screw) an unsteady machine could lead to false measurements.

  • Page 9: Introduction Of Panel

    B. Explanation of panel: Weight / outside Weight / inside Car / truck-display Balancing program Position display / inside Position display / outside Wheel size - Distance - Width - Diameter Change balancing mode Reset Exact gram display STOP START Change mode car / truck Key-combinations:...

  • Page 10: Mount The Thread Axle To The Drive Shaft / Fix Wheel

    C. Mount the threaded axle to the drive shaft Use the allen screw to attach the threaded shaft to the drive shaft. Fix the wheel Check the wheel Remove old weights and clean the wheel. Check tire pressure, according to Correct prescribed pressure.

  • Page 11: Putting Through The Power And Number Input

    D. Putting through the power and number input D.1 Putting through the power Switching on power, the machine display board shows that it marks “001”, in the computer memory, it shows A-8.0 several seconds later which indicates that machine operation is normal. Then input set wheel size, see following instruction about input method (note that balancing machine computer automatically sets up dynamic balance each time when turning on computer) Technical changes for purposes of a technical advancement as well as deviation in colour, errors and printing mistakes are reserved.

  • Page 12: Size Imput / Balancing Examples

    E.1 Size input ● For example testing luxurious wheel rim of Santana, please see picture on last page , use ruler that this machine has to measure gap size between machine and tyre: A=7.5cm Press↑, number increases Press↓, number decreases ●...

  • Page 13: Precautions / Balancing Experiences / Self Correction

    F.1 Precautions in the process of use and balancing experiences !Attention: ·When power starts, push the wheel by hands to assist starting which will extend motor’s life. Due to balance angle error, please find out by yourself when this machine rotates wheel to find balance point, pay attention which direction is much more accurate when wheel turns inward or outward.
  • Page 14 F.2 Self correction Self correction has been finished in the factory. If you use for many years and change part or doubt balance to be a big error, you can self correct it again.( Choose one medium-sized tyre to install on main shaft, uneventy of steel rim on both sides of wheel is relatively slight, only 13 inches and 14 inches).
  • Page 15 A. Generally use lead lump of 100g inaccurately. B. The edge outside wheel rim is irregular, can take down the lead lump and strike lead lump again on the opposite side and make comparation through drawing 2 times average. ● Self correction cann’t be done because of different practices, fingers can slightly give a push. Time difference between two fingers is half a second.

  • Page 16: Diagnosis Of Automatic Trouble

    4. Diagnosis of automatic trouble Code Meaning Cause Solution Err 1 Main shaft not rotating 1. Motor fault 1. Check motor 2. Position sensor 2. Check position sensor 3. Power board 3. Check power board 4. CPU 4. Change CPU 5.

  • Page 17: Options For Mode Of Balancing

    5. Options for mode of balancing Balancing programs Balancing program features Choose following balancing programs depending to wheel material and rim design pressing F-key several times. Active balancing program will be shown at control panel. Dynamic balancing: standard, balancing weight fixed for light alloy wheels at rim flange.

  • Page 18: Circiut Diagram (220 V)

    6. Circuit diagram (220 V) Technical changes for purposes of a technical advancement as well as deviation in colour, errors and printing mistakes are reserved.

  • Page 19: Circiut Diagram (400 V)

    7. Circuit diagram (400 V) Technical changes for purposes of a technical advancement as well as deviation in colour, errors and printing mistakes are reserved.

  • Page 20: Exploded Drawings

    8. Exploded drawings Technical changes for purposes of a technical advancement as well as deviation in colour, errors and printing mistakes are reserved.
  • Page 21 Technical changes for purposes of a technical advancement as well as deviation in colour, errors and printing mistakes are reserved.
  • Page 22 Technical changes for purposes of a technical advancement as well as deviation in colour, errors and printing mistakes are reserved.

  • Page 23: Spare Part List

    8. Spare part list Qty. Qty. Code Description Code Description B-004-080001-0 S-100-085000-0 Set of cones S-100-000020-0 Complete Shaft P-850-330000-0 Spring B-040-123030-1 Washer P-850-200000-0 Plastic cover P-850-080000-0 Through bolt (H) PX-850-200200-0 Support B-010-100551-0 S-131-000020-0 Sensor assembly Screw B-040-124030-1 B-004-160001-0 Washer B-048-122830-1 Butterfly washer B-004-120001-2 PX-850-010000-10...
  • Page 24 9. Spare part list Bild Bezeichnung Code Menge W-070-000101-1 Centring cone for truck 1# W-070-000101-2 Centring cone for truck 2# LARGE SPACING RING（match W-070-000007-1 Large cone for truck1#&2#） LARGE SPACING RING( match W-070-000007-2 Large cone for truck 3#) Large cone for truck 2#（optional） W-070-000101-3 W-070-000101-4 Large cone for truck 3#...
  • Page 25 W-070-000008-2 COUNTER WEIGHT 100g W-070-000008-3 COUNTER WEIGHT 150g W-070-000008-4 COUNTER WEIGHT 200g W-070-000008-5 COUNTER WEIGHT 250g W-070-000008-6 COUNTER WEIGHT 300g Y-032-020850-0 MANUAL W-070-000000-7 CALIPER S-108-000010-0 PLIER W-070-000103-1 LOCKING NUT W-070-000000-5 HANDLE Technical changes for purposes of a technical advancement as well as deviation in colour, errors and printing mistakes are reserved.

  • Page 26: Space For Notes

    Space for notes: Technical changes for purposes of a technical advancement as well as deviation in colour, errors and printing mistakes are reserved.

  • Page 27: Eg-Declaration

    Technical changes for purposes of a technical advancement as well as deviation in colour, errors and printing mistakes are reserved.

  • Page 28: Video Link (Qr Code)

    12. Video link Look at our videos! A helpful addition to the manual. Just scan QR-Code or copy this link: Technical changes for purposes of a technical advancement as well as deviation in colour, errors and printing mistakes are reserved.
  • Page 29 Technical changes for purposes of a technical advancement as well as deviation in colour, errors and printing mistakes are reserved.

Table of Contents