Advertisement
Quick Links
Advertisement
Related Manuals for Lander BAE HAWK
Summary of Contents for Lander BAE HAWK
- Page 1 BAE HAWK OPERATIONAL MANUAL...
-
Page 2: Specifications
Please read before operating this system! e would like thank you for purchasing our new product –Bae Hawk designed for the hobby enthusiast. Base on its full - scale counterpart, this Great British Jet can finish loops, inverted flight and rolls and other aerobatics easily. -
Page 3: Main Accessories
Main Accessories Main Fuselage Main Wing Set Horizontal Stabilizer Vertical Stabilizer Both Side Intake Set EDF Cover Set Rocker Tube Canopy Set Horizontal Stabilizer Mechanical Set Lighting System Set Full Set Retractable Landing Gear Remarks: 1) Operational Manual (included) 2) 5 Min. epoxy set (included) 3) Y Cord X 3 pcs (included except ARF version) 4) Push rods for Elevator, Rudder, Aileron, and Retract Gear &... -
Page 4: Assembling The Aircraft
Assembling the aircraft 1) Nose retract gear has been assembled by factory. 1) Using epoxy to glue up the nose gear ply wood on the related compartment and install both of retract gear & steering servos on the specific position then link up the push rob as shown. - Page 5 1) Find out the horizontal stabilizer set and mechanical set. 2) Using some epoxy to glue up both side horizontal stabilizer on the mechanical set first 1) Install both side horizontal stabilizer on the main fuselage and using the provided screws to lock up the stopper as shown 1) Install the vertical stabilizer.
- Page 6 1) Using some epoxy to glue on the vertical stabilizer on the main fuselage. 1) Install the main retracts landing gear on the main wing. 1) Using the attached screws to tight up the main retract landing gear on the gear bay square hard wood.
- Page 7 1)Install the aileron servos. 1) Using a Y cord to link up both servos cord as shown. 1) Install both side of intake set - 7 -...
- Page 8 1) Using epoxy to glue up both side intakes set on the main fuselage. 1) Install the Rclander 64mm metal EDF set with ESC. 1）Using the attached two pieces strong double foam tape (pls cut out from two to four pieces) to put on the EDF set bay first. - 8 -...
- Page 9 1) Take some force to install the EDF set on the bay as shown then use some hot melt glue on the gap in order to strengthen the tighten of the EDF on the bay of main fuselage. 1) Using the attached clear pvc sheet and two screws to tight up the ESC on the bay of the main fuselage as shown.
- Page 10 1) Two 1.2mm wire push robs are the elevator then 1.4mm wire push rob is for rudder and link up the related control horn as shown. 1) Connect both 1.2mm push robs with two elevator servos (remind to take one reverse operation direction servo for elevator) 2) Connect the 1.4mm push rob with the...
- Page 11 1) Using the attached two 3X 18mm screw to lock up the EDF set cover on the main fuselage. 1) Install the battery & Receiver compartment ply wood. 1) Double check the nose gear, steering and elevator push rob with the related servos are doing well before glue up the ply wood as shown.
- Page 12 1) Install the main canopy set. 1) The canopy set is used push in method to install into main fuselage and pushes down the front canopy with a click sound once lock up. 2) Hand holds the front canopy and pull up to open it for changing the battery or doing any maintenance issue..
- Page 13 - 13 -...
- Page 14 Flight: To keep Bae Hawk flying only need 50% of the maximum power, it is a good idea to fly with power for a while and glide for a while. In this way you can prolong the maximum flight time and familiarize yourself with landing approaches.