Advertisement
Tetra
miniMAX MS
®
RISK OF ELECTRIC SHOCK
∙
Turn power off before inspection, installation or removal.
∙
Properly ground power supply enclosure.
RISK OF FIRE
∙
Use only suitably approved wire for input/output connections.
Minimum size 18 AWG (0.82mm
∙
Follow all local codes.
∙
Not to be submerged or used in a marine environment.
RISK OF FIRE OR ELECTRIC SHOCK
∙
LED Retrofit Kit installation requires knowledge of
sign electrical systems. If not qualified, do not attempt
installation. Contact a qualified electrician.
∙
Install this kit only in host signs that have been identified in
the installation instructions and where the input rating of the
retrofit kit does not exceed the input rating of the sign.
∙
Installation of this LED retrofit kit may involve drilling or
punching of holes into the structure of the sign. Check
for enclosed wiring and components to avoid damage to
wiring and electrical parts.
∙
Do not make or alter any open holes in an enclosure of
wiring or electrical components during kit installation.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This Class [A] RFLD complies with the Canadian standard ICES-005. Ce DEFR de la classe [A] est conforme à la NMB-005 du Canada.
This product is intended solely for the use of non-residential signage lighting and is not intended for use in any other applications.
WARNING / AVERTISSEMENT
)
2
UL WARNING/AVERTISSEMENT UL
RISQUE D'INCENDIE OU DE CHOC ÉLECTRIQUE
∙
L'installation de l'équipement de remplacement DEL exige Ia connaissance des
systèmes électriques pour enseignes. Si non qualifié, ne tentez pas d'installation.
Veuillez contacter un électricien qualifié.
∙
Risque d'incendie ou de choc électrique. Installez cet ensemble seulement dans des
enseignes hôtes qui ont été identifiés dans les instructions d'installation et dont la
capacité d'entrée de l'ensemble ne dépasse pas la capacité d'entrée de l'enseigne.
∙
L'installation de cet équipement de remplacement DEL peut impliquer le perçage ou le
poinçonnage de trous dans la structure du panneau Vérifiez le câblage et les composants
inclus pour éviter d'endommager le câblage et les composants électriques.
∙
Ne pas faire ou modifier les trous ouverts dans une enceinte de câblage ou de
composants électriques pendant l'installation de cet équipement de remplacement
DEL.
IP66 rated: separate enclosure required for outdoor use, UL damp location rated.
Conforms to the following standards:
RISQUES DE DÉCHARGES ÉLECTRIQUES
∙
Coupez l'alimentation avant l'inspection, l'installation ou le déplacement.
∙
Assurez-vous de correctement mettre à terre l'alimentation électrique.
RISQUES D'INCENDIE
∙
N'utilisez que des fils approuvés par UL pour les entrées/sorties de
connexion. Taille minimum 18 AWG (0.82mm
∙
Respectez tous les codes locaux.
∙
Ne pas submerger ou installer dans un environnement marin.
2
Installation Guide
)
2
Advertisement
