Summary of Contents for Infinite Radio Waves SP Series
- Page 1 Standard Pole Mount Parabolic Antenna Mounting Instructions 3 ft. (90cm) & 4 ft. (120cm) 495R Billerica Ave. – North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 Email: sales@radiowaves.com...
- Page 2 IMPORTANT! Please read instructions through completely before beginning installation. Caution should be used. Qualified persons experienced with antenna assembly and installation are required for installation. DISCLAIMER Radio Waves Inc. disclaims any responsibility or liability for damage or injury resulting from incorrect or unsafe installation practices Table of Contents Page Mechanical Specifications...
- Page 3 RadioWaves Antennas Mechanical Specifications Elevation Range: ±15° • Azimuth Range: ±15° • Mounts to 3” - 4 1/2” outside diameter vertical pipemast • Weight (including mount): • Antenna Size SP Series SP W/Radome HP Series 3 ft. (90cm): 43 lb.
- Page 4 90cm/36 in & 120cm/48 in Antenna Mounting Procedure The following describes the general installation practices that apply to the antenna mount and antenna assembly. IMPORTANT! Read instructions completely before assembling or installing the antenna. This assembly requires qualified personnel familiar with microwave antenna assembly and installation. Unpacking and Preparation Carefully unpack the antenna assembly and mount parts from its shipping container.
- Page 5 List of Contents Item No. Quantity Part Number Description 100780-1 Pole Mount Kit 100782-1 Pole Mounting Bracket 100781-1 Antenna Mounting Pipe 100797-1 Bracket, Azimuth Adjust 101094-1 Eye Bolt,3/8-16 Thread (Galvanized steel) 101150-1 Eye Bolt,1/2-13 Thread (Galvanized steel) 100792 Spacer, 1/4-20 Stud (As required) Antenna Assembly 100795-1...
- Page 6 Antenna Assembly Step 1 Attach antenna mounting pipe 2 to the Antenna ring with (4) 3/8-16 x 7/8 long hex head bolts, split lock washers and flat washer. Step 2 Attach azimuth bracket 3 to the pole with 3/8-16 U-bolt. Secure to pole with flat and split lock washers and silicon bronze hex nuts.
- Page 7 Step 3 Attach pole mounting bracket 1 to the 4-1/2” diameter pole using 1/2- 13 U-bolts. Use the azimuth adjust U-bolt as a rest, face the bracket towards the desired antenna direction and secure the 1/2-13 U-bolts with the appropriate hardware. Tighten until the bracket is snug to pole - do not fully tighten at this time.
- Page 8 Step 5 Install ½-13 galvanized hex nut flat washer and split lock washer on the elevation adjust rod 6 Thread the nut approximately 20 inches up (as shown). Slide the adjustment rod through the slot of the pole mount bracket opposite the tab being used for the azimuth adjust rod. Secure with appropriate hardware as shown.
- Page 9 Step 7 Assemble the elevation adjust rod 6 to the antenna assembly by installing the bushing through the adjust rod hole and securing to bracket on antenna assembly with 3/8-16 x 2” long hex head bolt and appropriate hardware as shown. Position the antenna such that the elevation adjust rod is aligned perpendicular to the mount.
- Page 10 Feed and RFU Attachment Information The feed is normally attached to the rear of the antenna in the vertical polarization position. Horizontal polarization is set by removing the (4) 8-32 pan head screws and washers, rotating the feed assembly 90 degrees such that the arrow on the feed is pointing to the “H” on the antenna backshell, and re-attaching the 8-32 hardware.
- Page 11 SAFETY INFORMATION This Information May Save You From Death or Injury Do not attempt to install or dismantle any Radio Waves Inc. products until you have read and understood the information and instructions in this document. Installations: Only trained professional installers should be used to install or dismantle antennas, mounts, and related hardware.