Download Print this page
Sealey 2200HL.V3 Instructions
Sealey 2200HL.V3 Instructions

Sealey 2200HL.V3 Instructions

Trolley jack 2tonne high lift low entry

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear
instruction
safety
manual
footwear
1. SAFETY
9
Ensure the jack is in sound condition and good working order. Take action for immediate repair or
replacement of damaged parts.
9
Use genuine parts only. The use of unauthorised parts may be dangerous and will invalidate the
warranty.
9
Locate the jack in a suitable, well lit, work area.
9
Keep work area clean and tidy and free from unrelated materials.
9
Use jack on a level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
9
Place suitable wheel chocks under wheels of the vehicle.
9
Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear
(or "Park" if automatic).
9
Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc.,
to allow for vehicle tilting.
9
Ensure there are no passengers in the vehicle.
9
Ensure all non-essential persons keep a safe distance whilst the jack is in use.
9
Only place jack saddle under those lifting points recommended by the vehicle manufacturer
(see vehicle handbook).
9
Check the lifting point is stable and centred on the jack saddle.
9
Ensure the jack wheels are free to move and that there are no obstructions.
9
Use suitable capacity axle stands under the vehicle before proceeding with any task.
9
Ensure there are no persons or obstructions beneath the vehicle before lowering.
Use a qualified person to maintain or repair the jack hydraulic system.
9
9
When not in use store jack, fully lowered, in a safe, dry, childproof area.
8
DANGER: Use the jack for lifting only.
8
DO NOT use for supporting the lifted load.
8
DO NOT operate the jack if damaged.
8
DO NOT allow untrained persons to operate the jack.
8
DO NOT exceed the rated capacity of the jack.
8
DO NOT allow the vehicle to move while supported by the jack, or use the jack to move the
vehicle.
8
DO NOT jack the vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous
substances.
8
DO NOT work under the vehicle until axle stands have been correctly positioned.
8
DO NOT use the jack for purposes other than that for which it is intended.
8
DO NOT top up the hydraulic system with brake fluid. Use hydraulic jack oil only.
8
DO NOT adjust the safety overload valve.
2. INTRODUCTION
High lift jack arm with incredibly low access height of just 80mm. Fitted with quick lift foot pedal and dead man's control. Heavy-duty long steel
chassis with wide wheelbase provides inherent stability and easy access to deep set jacking points. Fitted with one-piece hydraulic unit with
built-in safety overload protection.
3. SPECIFICATION
Model no: ............................................................. 2200HL.V3
Capacity: ..................................................................... 2tonne
Minimum saddle height: ............................................... 80mm
Maximum saddle height: ............................................ 805mm
Maximum chassis height: ........................................... 220mm
Length: ....................................................................... 950mm
Weight:........................................................................... 51kg
© Jack Sealey Limited
INSTRUCTIONS FOR
TROLLEY JACK 2TONNE HIGH LIFT LOW ENTRY
2200HL.V3
MODEL NO:
Original Language Version
Apply
Chock
Wheels
Never
exceed
X2
2200HL.V3 | Issue:1 31/08/17

Advertisement

loading

Summary of Contents for Sealey 2200HL.V3

  • Page 1 2200HL.V3 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 6.3.2. Remove the filler plug located on top of the ram. Correct oil level is just below the lower edge of the filling hole. Approximate oil capacity - 0.3ltr. IMPORTANT: DO NOT overfill as this may effect the smooth operation of the jack. NOTE: Use a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL. ‰ WARNING: DO NOT use brake fluid or any fluid other than hydraulic jack fluid, as this may cause serious damage to the jack and will invalidate the warranty! 6.4. Before each use check for broken, cracked, bent, or loose parts, or any visible damage to ram, pump, saddle, lifting arm, frame and all parts including nuts, bolts, pins and other fasteners.
  • Page 3 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...