Error Codes - Arctic Spa ARCTIC ESSENTIALS Y Series Owner's Manual

operation. Press Pump 1
or Pump 2 (if available) to
restart the system before the
Arctic Essentials Owners Manual
expiration of the 30 minute
delay. When the system
resumes its normal operation,
the display shows "On" for
3 seconds.
Programming Steps
Program menu
The program menu is
accessible by holding down
the Light key for 5 seconds.
In the program menu the
following parameters can be
set: clock, the filter or purge
cycles, economy mode and
temperature units. While you
are in the program menu,
use the Up or Down key to
adjust the parameters and
use the Light key to jump
to the next parameter.
The changes will be saved
after the confirmation of
Setting filter or purge
cycle start time
The display will show FSxx,
"xx" representing the starting
hour of the cycle. Use the Up
or Down key to adjust
the hours. Use the Light
key to jump to the next
parameter, filter duration (Fd).
Setting temperature unit
Water temperature can be
displayed in either Fahrenheit
(°F) or Celsius (°C). The dis-
play will show F or C.
Use the Up or Down key
to change the setting. Use
the Light key to save all the
parameters.
Troubleshooting section
Should an error occur, the display will show one of the following error messages toggled with the clock and the water temperature.
15
in.xe error codes
* If single speed pump: press Pump key to turn pump on. Press Pump key
again to turn pump off.
Setting the clock
the last parameter only.
Enter the program menu by
If there is no action taken holding down the Light key
for 10 seconds, the system for 5 seconds. The display will
will exit the program menu show the current clock setting
without saving any changes. with the hour flashing.
Depending on factory settings
your system may be set to
24-hour time or 12-hour time.
Setting the hour: Use the Up
or Down keys to adjust the
hours. Press the Light key to
jump to the next parameter,
the minutes.
Setting filter cycle Setting filter or purge
duration cycle frequency
(not available on purge The display will show FFxx,
systems) "xx" representing the number
of cycles per day. Use the Up
or Down key to adjust the
The display will show Fdxx,
"xx" representing the dura- frequency. Use the Light key
to jump to the next parameter,
tion in hours of the filter
economy mode (EP).
cycle. Use the Up or Down
key to adjust the duration.
Use the Light key to jump to The "Filter cycle" indicator
lights up when filter is on
the next parameter, filter or
and flashes when suspended.
purge frequency (FF).
0 = no filtration
24 = continuous filtration
It is not recommended to set
this to "0".
Smart Winter Mode Cooldown
Our Smart Winter Mode
After heating the spa water
protects your system from to the desired Set Point, the
the cold by turning pumps on heater is turned off, but its
several times a day to prevent
associated pump (Pump 1
water from freezing in pipes. low-speed or CP) remains
on for a predetermined
The "SWM" indicator
period of time to ensure
lights up when freezing is
adequate cooling of the
detected and flashes when heating element, prolonging
the purge is active. its useful life.
Description
NOT the current
water temperature!
Programming the filter/
purge cycles
Setting the minutes: Use the
Up or Down keys to adjust
Depending on system
the minutes. Press the Light
configuration your spa
key to jump to the next
will perform either a filter
parameter, the filter or purge
or a purge cycle. The filter
start time (FS).
cycle menu consists of the
following parameters: the
start time (FS), the duration
(Fd) and the frequency
(FF). The purge cycle menu
consists of the following
parameters: the start time (FS)
and the frequency (FF).
Setting economy start time
Setting economy mode
This mode allows you to The display will show ESxx,
"xx" representing the hour at
lower the temperature set
point of the spa by 20 °F which the economy mode
(11 °C) during a certain period will become active. Use the
of the day. Up or Down key to adjust
the hour. Use the Light key to
The display will show EPx, "x" jump to the next parameter,
representing the state of the economy duration (Ed).
programmed economy
When the Economy mode
(0 = disabled, 1 = enabled).
Use the arrow keys to enable is ON, the display will toggle
or disable economy mode. between the "Eco" message,
the time, and the water
Use the Light key to jump to
the next parameter, economy temperature.
start time (ES).
Water temperature
regulation
Every 15 to 90 minutes
the pump will run to ensure
accurate water temperature
readings as well as avoid
heater activation in dry
conditions. After verifying
pump activation and taking
a water temperature reading
if required, the system
automatically turns the heater
on to reach and maintain
water temperature at
Set Point.
Indicator flashes when
taking water tempe-
rature reading.
A filter cycle consists of
starting all the pumps and
blower in high speed for
1 minute (purge step) then,
the pump associated with
the filter will run in low speed
for the remaining duration
of the filter cycle (clean step).
A purge cycle is used when
the spa is equipped with a 24
hour circulation pump which
provides a continuous clean
step. It consists of starting all
the pumps and blower in
high speed for 1 minute.
Setting economy duration
The display will show
Edxx, "xx" representing
the duration in hour of the
economy mode. Use the Up
or Down key to adjust the
hour. Use the Light key to
jump to the next parameter,
temperature unit.
24 = continuous economy