Arctic Spa ARCTIC ESSENTIALS Y Series Owner's Manual page 15

Spa Functions
Off Mode Pump 1
Pressing Pump 1 for 5 seconds Press Pump 1 key to turn
will enable the Off mode. Pump 1 on at low speed.
This mode allows you to Press a second time to turn
stop all outputs including pump to high speed (with a
automatic functions such as dual-speed pump*). A third
filter cycle, heat request and time turns pump off. A built-in
smart winter mode for timer automatically turns
30 minutes to perform quick pump off after 20 minutes,
spa maintenance. When Off unless pump has been
mode is active, the display manually deactivated first.
will toggle between the "OFF"
message, the clock and the The "Pump 1" indicator
water temperature. lights up when Pump 1 is on.
The spa light will flash for With a dual-speed pump,
a few seconds before the the indicator will flash when
end of the 30 minutes to pump 1 is on at low speed.
warn you that the system is
about to resume its normal
operation. Press Pump 1
or Pump 2 (if available) to
restart the system before the
expiration of the 30 minute
delay. When the system
resumes its normal operation,
* If single speed pump: press Pump key to turn pump on. Press Pump key
the display shows "On" for
again to turn pump off.
3 seconds.
Programming Steps
Program menu
the last parameter only.
The program menu is
accessible by holding down If there is no action taken
for 10 seconds, the system
the Light key for 5 seconds.
will exit the program menu
In the program menu the
following parameters can be without saving any changes.
set: clock, the filter or purge
cycles, economy mode and
temperature units. While you
are in the program menu,
use the Up or Down key to
adjust the parameters and
use the Light key to jump
to the next parameter.
The changes will be saved
after the confirmation of
Indicator lights
Down
Pump 2 key Light key
Not available on all models Press Light key to turn light
on. A second press turns
Press Pump 2 key to turn light off. A built-in timer
Pump 2 on at low speed. automatically turns light
Press a second time to turn off after 2 hours, unless it
pump to high speed (with a has been manually
dual-speed pump*). A third deactivated first.
time turns pump off. A built-in
timer automatically turns The "Light" indicator lights up
pump off after 20 minutes, when light is on.
unless pump has been
manually deactivated first.
The "Pump 2" indicator
lights up when Pump 2 is on.
With a dual-speed pump,
the indicator will flash when
pump 2 is on at low speed.
Setting the clock
Enter the program menu by Setting the minutes: Use the
holding down the Light key Up or Down keys to adjust
for 5 seconds. The display will the minutes. Press the Light
show the current clock setting key to jump to the next
with the hour flashing. parameter, the filter or purge
start time (FS).
Depending on factory settings
your system may be set to
24-hour time or 12-hour time.
Setting the hour: Use the Up
or Down keys to adjust the
hours. Press the Light key to
jump to the next parameter,
the minutes.
Indicator lights
Up/Down keys
Use Up or Down key to set
desired water temperature.
The temperature setting will
be displayed for 2 seconds to
confirm your new selection.
2 pump spas have a
combined Up/Down key.
Hold the button to increase
the parameter and release
the button to stop. Hold
the button again to decrease
the parameter.
The "Set Point" icon
indicates that the
display shows the
desired temperature,
NOT the current
water temperature!
Programming the filter/
A filter cycle consists of
purge cycles
starting all the pumps and
blower in high speed for
Depending on system 1 minute (purge step) then,
configuration your spa the pump associated with
the filter will run in low speed
will perform either a filter
or a purge cycle. The filter for the remaining duration
cycle menu consists of the of the filter cycle (clean step).
following parameters: the
start time (FS), the duration A purge cycle is used when
(Fd) and the frequency the spa is equipped with a 24
hour circulation pump which
(FF). The purge cycle menu
consists of the following provides a continuous clean
step. It consists of starting all
parameters: the start time (FS)
the pumps and blower in
and the frequency (FF).
high speed for 1 minute.
Up / Down
14