DSE 871 Series Installation Instructions

ACCESSING THE FRONT PANEL CONFIGURATION EDITOR

NOTE: Selected parameters can be configured via the front panel editor. NOTE: Selected parameters can be configured via the front panel editor. Selected parameters can be configured via the front panel editor. More Selected parameters can be configured via the front panel editor.
NOTE: NOTE: Selected parameters can be configured via the front panel editor. Selected parameters can be configured via the front panel editor. Selected parameters can be configured via the front panel editor. Selected parameters can be configured via the front panel editor.
comprehensive module configuration is possible using the comprehensive module configuration is possible using the PC C
comprehensive module configuration is possible using the comprehensive module configuration is possible using the
S S S S oftware oftware. . . . Please contact us for further details Please contact us for further details. . . .
oftware oftware Please contact us for further details Please contact us for further details
•
Ensure the engine is at rest and the module is in STOP mode by pressing the Stop/Reset Ensure the engine is at rest and the module is in STOP mode by pressing the Stop/Reset
•
Press the Stop/Reset
•
If a module security PIN has been set, the PIN number request is then
shown :
•
Press , the first '#' changes to '0'. Press
correct value.
•
Press
show '#' for security.
•
Repeat this process for the other digits of the PIN number. You can press Repeat this process for the other digits of the PIN number. You can press
to move back to adjust one of the previous digits.
•
When is pressed after editing the final PIN digit, the PIN is checked for validity. If the number is is pressed after editing the final PIN digit, the PIN is checked for validity. If the number is
not correct, you must re-enter the PIN.
•
If the PIN has been successfully entered (or the module PIN has not been If the PIN has been successfully entered (or the module PIN has not been
enabled), the editor is displayed :

EDITING A PARAMETER

•
Enter the editor as described above.
•
Press the left or right buttons to cycle to the section you wish to view/change. Press the left or right buttons to cycle to the section you wish to view/change.
•
Press the up or down buttons to select the parameter you wish to view/change within the currently
selected section.
•
To edit the parameter, press
you are editing the value.
•
Press the up or down buttons to change the parameter to the required value.
•
Press to save the value. The parameter ceases flashing to indicate that it has been saved.
•
To exit the editor at any time, press and hold the
NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to
ensure security. ensure ensure ensure security. security. security.
NOTE: NOTE: The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or
NOTE: NOTE: The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or
a a a a u u u u t t t t o o o o m m m m a a a a t t t t i i i i c c c c a a a a l l l l l l l l y y y y ) ) ) ) t t t t o o o o e e e e n n n n s s s s u u u u r r r r e e e e s s s s e e e e c c c c u u u u r r r r i i i i t t t t y y y y . . . .
D E E P S E A E L E C T R O N I C S D E E P S E A E L E C T R O N I C S
8 7 1 x I N S T A L L A T I O N I N S T R U C T I O N S 8 7 1 x I N S T A L L A T I O N I N S T R U C T I O N S
and Info
(right) when the first digit is correctly entered. The digit you have just entered will now when the first digit is correctly entered. The digit you have just entered will now
buttons to select the parameter you wish to view/change within the currently
to enter edit mode. The parameter begins to flash to indicate that to enter edit mode. The parameter begins to flash to indicate that
change the parameter to the required value.
buttons simultaneously.
(up) or
flashing to indicate that it has been saved.
button.
053-071
ISSUE 1
More
More More
PC Configuration onfiguration onfiguration onfiguration Suite Suite
PC C PC C onfiguration onfiguration onfiguration onfiguration Suite Suite
(down) (down) to adjust it to the
(left) if you need
button.