koppel KFM-36E0C Operation Manual

Operation Manual
Package Split Type
Air Conditioner
KFM-36E0C KFM-36E0C
KFM-36E0W
1. SAFETY PRECAUTION
• Please read this manual carefully before operating the air conditioner.
• Pay special attention to signs "WARNING". The "Warning" section contains
matters, which, if not observed strictly, may cause death or serious injury.
• Please follow all instructions strictly to help ensure your safety.
!
WARNING
• All wiring must conform to local and national electrical codes.
• To avoid possible electrical shock, you must ground your air conditioner.
• This air conditioner requires a separate power supply on a separately fused circuit.
• Do not insert your finger, a sticker, or any other object into the air inlet and air
outlet.
• Do not expose the skin directly to the indoor airflow for an extended period of time.
• • Do not install the outdoor condensing unit near flammable gas. The condensing Do not install the outdoor condensing unit near flammable gas. The condensing
unit may catch fire if flammable gas leaks.
!
REMINDER
• Keep this manual for future reference as it contains important installation and
safety precautions.
Call for service when:
• Abnormal operating noise is heard.
• A fuse blows or a circuit breaker trips frequently.
• The Controls do not work properly.
2. CONTROL
CONTROL PAD
MODE SELECTOR (LONG PRESS FOR 3 SEC)
AIR SWING (SHORT PRESS)
FAN SPEED BUTTON
TEMPERATURE UP BUTTON
TEMPERATURE DOWN BUTTON
POWER ON / OFF BUTTON
SLEEP MODE
INDICATOR
FAN "ON"
INDICATOR
FAN SPEED
TEMPERATURE
SETTING INDICATOR
FAN SPEED BUTTON
SLEEP BUTTON
AIR SWING BUTTON *
TIMER BUTTON
REMOTE CONTROL UNIT
(OPTIONAL – CAN BE PURCHASED SEPARATELY)
Koppel, Inc.
106 Industry Drive, Carmelray
Industrial Park I, Brgy. Canlubang,
Calamba City, Laguna 4028, Philippines
NOTE: BUTTONS ARE HIGHLY TOUCH SENSITIVE.
TIMER "ON"
INDICATOR
MODE
INDICATOR
TEMPERATURE/ TIMER
ADJUSTMENT BUTTON
"ON/OFF" BUTTON
MODE SELECTOR
BUTTON
"SEND" BUTTON
"CANCEL" BUTTON "CANCEL" BUTTON
• Pressing the AIR SWING BUTTON
activates/deactivates left to right
swiveling motion of the supply grille.
3. USING THE CONTROL PAD
MODE SELECTION DISPLAY
FAN
COOL
DRY
FAN SPEED SELECTION
LOW
MEDIUM
HIGH
AUTO
Power On the Unit
Turn on the power to the unit by pressing the
When turned on, the system will operate to the last setting. The LCD Display will
show the system status.
Mode Setting
Press and Hold the button for three (3) seconds to change the mode.
FAN COOL
The LCD shows or or
respectively.
Fan Speed Setting
Press button to select the fan speed.
While Auto speed is set, the fan speed (High, Medium, Low) will be changed
automatically according to the system circulation.
Note: 1. The Auto speed cannot be set in Fan mode.
2. The indoor fan may not work if some functions or protections are activated.
Temperature Setting
Press or button to set the temperature in a range of 17 – 30°C.
NOTE: The temperature cannot be set while in the FAN mode.
The numeric display will blink the new setting for five (5) seconds. Then it will stop
blinking and show its idle state which may be the return-air (room) temperature or may
be set temperature. It depends on the option setting.
Press and hold and buttons for five (5) seconds to change this setting. The numeric
display will show for room temperature as idle state or it will show
for idle state.
Sweep Activation
Press button to turn on and off the air swing function.
LED brightness
Press and hold and buttons for three (3) seconds to dim the brightness of
LED.
To set the brightness back to normal, press and hold
(3) seconds again or turn off then turn on the air conditioner again. (3) seconds again or turn off then turn on the air conditioner again.
24 Hour Timer Setting
* Can be activated only by using the Remote control wireless handset.
The air-conditioner can be programmed to turn ON and OFF in advance by setting
the timer on the Remote Controller.
Sleep Mode
* Can be activated only by using the Remote control wireless handset.
Pressing the SLEEP button on the remote controller will activate the sleep mode.
One (1) hour after activation of sleep mode, the controlled temperature will be adjusted
automatically after 1 hour. Temperature will be raised by one degree (1°C) from set
temperature for more comfortable and energy saving at night time.
NOTE: The Sleep function can be used only in Cool mode. If the mode is changed the
Sleep function will be cancelled.
TEMPERATURE DISPLAY
IN °C
COMPRESSOR ON
INDICATOR
NOTE:
BUTTONS ARE HIGHLY TOUCH
SENSITIVE.
button on the control pad.
DRY
symbol for FAN, COOL, and DRY mode
for set temperature
and buttons for three