Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for koppel ERA series
Summary of Contents for koppel ERA series
-
Page 2: Table Of Contents
CONTENTS Safety Precautions................1 Identification of Parts..............2 Remote Controller................4 Operation Instructions..............6 Maintenance................8 Protection..................9 Troubleshooting................10 Installation Instructions..............11 Preparation Before Use Before using the air conditioner, be sure to check and preset the following: Remote Controller Presetting Each time the remote Controller gets a new set of batteries or is energized, the symbol will flash from COOL HEAT... -
Page 3: Safety Precautions
Safety Precautions Symbols in this Use and Care Manual are interpreted as shown below. Be sure to follow this instruction. Be sure not to do. Pay attention to such a situation. Remove the power source plug from a socket. Warning: Incorrect handling could cause a serious Grounding is essential. -
Page 4: Identification Of Parts
Identification of Parts Indoor Unit Air Intake Front Panel Emergency Panel Display Panel Air Outlet Vertical Adjustment Louver Horizontal Adjustment Louver Air Filter Remote Controller Air Intake Outdoor Unit Pipes and Power Connection Cord Drain Hose Note: Condensate water drains at COOLING or DRY operation. - Page 5 Identification of Parts Operating and Display Signal Receives Sleep Indicator Receive signal from It lights up during the the remote controller. set sleep function Timer Indicator It lights up during the Power Indicator set time. It lights up when power supply is on. Run Indicator It is on during TIMER...
-
Page 6: Remote Controller
Remote Controller Remote Controller The remote controller transmits signals to the system. ON/OFF button Used to start and stop operation . TIMER button SLEEP TIMER ON TMIER OFF FEEL AUTO Used to select TIMER operation. HIGH COOL HEAT SWING UP button Used to increase the set room temperature (16 and time(0.5~24h). - Page 7 Remote Controller Remote Controller How to Insert the Batteries Please slide and remove the cover. Remove the battery cover according to the arrow direction. Insert new batteries making sure that the (+) and (-) of Slide the cover battery are matched correctly. upwardly in the direction of the Re-attach the cover by sliding it back into position.
-
Page 8: Operation Instructions
Operation Instructions FEEL mode operation procedure FEEL mode automatically selects the operation mode(DRY,FAN,COOL) depending on the current room temperature . With the remote controller pointing toward the air conditioner. Turning on Press button. When the appliance receives the ON/OFF signal, the RUN indicator of the indoor unit lights up. SLEEP TIMER ON TMIER OFF FEEL... - Page 9 Operation Instructions TIMER mode It is convenient to set the timer on with TIMER button when you go out in the morning to achieve a comfortable room temperature when you get home. You can also set timer off at night to enjoy a good sleep. When the Remote When the Remote Controller is ON,press...
-
Page 10: Maintenance
Maintenance Air filter maintenance Front panel maintenance It is necessary to clean the air filter after using Turn off circuit breaker it for about 100 hours. Clean it as follows: Stop the appliance Grasp position "a" and remove the and pull outward to air filter. -
Page 11: Protection
Protection Operating condition Noise pollution The protective device may trip and stop the appliance in the cases listed below. Install the air conditioner at a place that can bear its weight in order to operate more quietly. Outdoor air temperature is over 52c COOLING Install the outdoor unit at a place where Room temperature is below 21c... -
Page 12: Troubleshooting
Troubleshooting The following cases may not always be a malfunction, please check it before asking for service. Check Trouble If batteries in the remote controller is already drained. Does not run If the protective device works to protect the appliance. If circuit breaker tripped or if the fuse is blown. -
Page 13: Installation Instructions
Installation Instructions Installation Diagram Distance from ceiling should be over 150 mm Distance from wall should be over 150mm Distance from the wall should be over 150mm Distance from floor should be over 2000mm over 500mm Air intake distance from the wall Air intake distance from should be over 300mm the wall should be... - Page 14 Installation Instructions Connecting of the Cable Front panel Wiring between the indoor and outdoor units: Terminal (inside) 1) Remove the PCB cover from the indoor unit; 2) Refer to the wiring diagram attached to indoor unit COVER COVER when connecting cords to indoor unit terminals; 3) Reinstall the PCB cover.
- Page 15 Installation Instructions Indoor Unit Installation 1. Installing the Mounting Plate Decide an installing location for the mounting plate according to the indoor unit location and piping direction. Keep the mounting plate horizontally with a horizontal ruler or dropping line. Drill holes of 32mm in depth on the wall for fixing the plate. Insert the plastic plugs to the hole, fix the mounting plate with tapping screws.
- Page 16 Installation Instructions NOTE NOTE Piping Joints Thermal Insulation: Wrap the piping joints with thermal insulation materials and then wrap with a vinyl tape. wrapped with vinyl type The temperature of refrigerant circuit Thermal insulation will be high, please keep the interconnection able away from the copper tube.
- Page 17 Installation Instructions 4. Connecting of the Cable Front panel Terminal (inside) Indoor Unit Connect the power connecting cord to the indoor unit by connecting the wires to the terminals on the control board individually in accordance with the outdoor unit Cabinet connection.
- Page 18 Installation Instructions Outdoor Unit Installation 1.Install Drain Port and Drain Hose (for heat-pump model only) The condensate drains from the outdoor unit when the unit operates in heating mode. In order to protect the environment, install a drain port and a drain hose to direct the condensate water. Just install the drain port and rubber washer to the chassis of the outdoor unit, then connect a drain hose to the port as the right figure shown.
-
Page 19: Circuit Diagram
Installation Instructions Interconnection Cable Take off the cover for Interconnection cable of outdoor unit. Take off the block for Interconnection cable, then put the core of the power wire to the terminal and fix it according to the diagrams pasted to indoor and outdoor unit separately. Fix the accessory cable with the Interconnection cable block. - Page 20 Installation Instructions How to Purge Air Tubes (1). Unscrew and remove caps from 2 and 3-way valves. (2). Unscrew and remove cap from service valve. (3). Connect vacuum pump flexible hose to the service valve. (4). Start vacuum pump for 10-15 minutes until reaching a vacuum of 10 mm Hg absolutes. (5).
- Page 21 KOPPEL,INC Branch Directory Paranaque Head Office: Severina Industrial Estate Km.16, South Superhighway Paranaque City 1700 Metro Manila, Philippines Trunkline: (02)823-2366-67/823-2370-72 Sales: (02)823-1580 24-Hour Hotlione:(02)843-4343 loc.21544 Service: (02)823-7310 Fax: (02)823-6995 Sales (02)823-6999 Service BRANCH Office: CEBU: DAVAO: J.P.Cabaguio Avenue A.Cortez Avenue,Mandaue City...