Cyber-shot w200 - powerful camera finished in smart silver aluminium, with 12.1 effective megapixels, hd output, double anti-blur and face detection technologies, zeiss 3x optical zoom lens, 2.5-inch lcd screen, viewfinder and stamina battery life. (126 pages)
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
PRINT Image Matching III: Compatible Approx. 0.3 m to 2.8 m (11 7/8 in. to 9 ft. 2 1/4 in.) (W) Approx. 1.5 m to 2 m (4 ft. 11 1/8 in. to 6 ft. 6 3/4 in.) (T) DSC-W830 – 2 –...
只能用同样类型或等效类型的电池来更换。 务必按照说明处置用完的电池。 • Color Indication of Appearance Parts Example: (SILVER) : Cabinet’s Color (Silver) : Parts Color • Abbreviation AUS : Australian model : Brazilian model : Chinese model CND : Canadian model : Korea model : Russian model DSC-W830...
Detailed Code Repaired by: Block C : Corrected by customer Indicates the appropriate Refer to “2-1-3. Self-diagnosis Code Table”. E : Corrected by service step to be taken. engineer E.g. 13 ..Format the “memory card”. 32 ..Turn on power again. DSC-W830...
Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit. (Note) Internal memory fault Turn the power off and on again. Note: After repair, be sure to perform “3-6. PROCESS AFTER FIXING FLASH ERROR”. DSC-W830...
USB SERIAL No. INPUT” and enter these IDs. Note: A newly entered Product ID is not always equal to the ID before board replacement. If the new ID differs from the previous ID, it may cause a difference from the ID registered by the customer. DSC-W830...
Page 13
If you pull on the wires, they might be broken. • The proper way to connect a connector is to grab the connector instead of the wires. If you push on the wires, they might be broken. DSC-W830...
Save precious data on a computer, etc. 1. MENU - (Settings) - (Internal Memory Tool) - [Format] - [OK] - Note Note that formatting permanently erases all data including even protected images. DSC-W830...
7) Disconnect the PC from the camera, and turn off the camera. Note: By turning off the camera, the write enable setting is reset. 3-5. POWER SUPPLY ON REPAIRING Use the battery (NP-BN) on repairing. The external battery source cannot be used on repairing. DSC-W830...
Be sure not to remove the battery pack while initializing. 3-7. DEDICATED A/V CABLE (OPTIONAL ACCESSORY) Dedicated A/V cable is not supplied with this model. For details of the dedicated A/V cable, refer to the Note 1 on the “ACCESSORIES”. DSC-W830...
1 kΩ/1 W Wrap insulating tape. Wrap insulating tape. Note: High-voltage cautions Discharging the Capacitor Short-circuit between two points with the short jig about 10 seconds. R:1 k Ω/1 W (Part code: 1-215-869-11) MA-1004 Flexible C901 Board MA-1004 Flexible Board DSC-W830...
Page 21
Hold the Lens Block at the Do not hold the following part. center of both sides. Zoom Motor Sensor Hold here. *Very weak Flexible Board Optical Stepping Motor *Very weak Flexible Board Lens Barrier Focus Lens Ornamental Ring *Very weak *Very weak DSC-W830...
Fold the notch 3 or 4 times repeatedly to break. Speaker Notch Harness (4) Precaution During Cabinet (Rear) Assy Installation When assembling, adjust the switch and Knob position. Switch Knob Remove the notch. Notch SW-1002 Board Cabinet (Rear) Assy DSC-W830...
1 Fit the four claws while inserting the Barrier Lever into the hole and attach the Barrier Assy. Barrier Claws Barrier Assy Lever Claws Hole 2 Peel off the release papers of the Barrier Tapes. Ornamental Ring A 3 Install the Ornamental Ring A and press it lightly. Barrier Assy Barrier Tapes Barrier Tapes DSC-W830...
Page 24
6 Remove the GearWorm Wheel, Gear A, and Gear B. Screws Screw Gear B Rear Mirror Plate Gear A Gear Worm Wheel 7 Remove the solder at two locations to detach the DC MotorWorm Assy and remove the two screws. Solders DC Motor Worm Assy Flexible Board Screws DSC-W830...
Page 25
6 Install the Rear Mirror Plate. 7 Tighten the four screws in the order of numbers in the figure below. 8 Apply a voltage of 2.5 V to the DC Motor and retract the Lens. Screws Screw Rear Mirror Plate DSC-W830...
Page 26
Install the two Sensors and attach the FG Leaf Spring. Note: Attach the FG Leaf Spring in the correct orientation. FG Leaf Spring FG Leaf Spring FG Leaf Spring Flexible Board Boss Boss Ribs Sensors Connector qs Perform the Flange Back Adjustment after the assembling. DSC-W830 4-10...
Page 27
To perform Destination Data Write for this model, the Adjust manual of the DSC-WX50 series must have been installed. Install the Adjust manual of the DSC-WX50 series in advance. (JAPANESE) これらの機種で調整を行なうには,アジャストマニュアルとアジャストステーションが必要です。 アジャストステーションとは 機種別のアジャストマニュアルを起動するためのソフトウェアです。 アジャストステーションのインストーラと一緒に,インストレーションマニュアルが付いていますので,内容を必ず確認して ください。 アジャストマニュアルとは デジタルカメラ及びカムコーダのサービス用の調整ソフトウェアで,調整及び各種動作確認を行うことが可能です。 アジャストマニュアルのインストーラと一緒に,インストレーションマニュアルが付いていますので,内容を必ず確認してく ださい。 注意1: インストールは必ず Adjust station を先に行なってください。 注意2: この機種で仕向け設定を行うには,DSC-WX50シリーズの Adjust manual がインストールされている必要 があります。 先に DSC-WX50 シリーズの Adjust manual をインストールしてください。 DSC-W830...