Page 1
Global Water 800-876-1172 • globalw.com FP101-FP201 Global Flow Probe User’s Manual The Leader in Water Instrumentation Visit Our Complete Online Catalog www.globalw.com Call (800) 876-1172, 7:30 AM to 4 PM Pacific Time International: US (916) 638-3429 • FAX: (916) 638-3270 E-mail: globalw@globalw.com...
Global Water 800-876-1172 • globalw.com Congratulations on your purchase of the Global Water Flow Probe. This instrument has been quality tested and approved for providing accurate and reliable measurements. We are confident that you will find the sensor to be a valuable asset for your application.
Your Flow Probe was carefully inspected and certified by our Quality Assurance Team before shipping. If any damage has occurred during shipping, please notify Global Water Instrumentation, Inc. and file a claim with the carrier involved. Use the checklist to ensure that you have received everything needed...
Point the propeller directly into the flow you wish to measure. Face the arrow inside the prop housing downstream. The FP101 probe handle is a two piece rod expandable from 3’ to 6’, and the FP201 is a three section rod expandable from 5’...
Global Water 800-876-1172 • globalw.com f. The average velocity (calculated with the Flow Probe in feet/second) times the cross-sectional area (square feet) equals flow in cubic feet per second (cfs), or Q = V x A. g. If the propeller gets fouled while measuring flow, clean it until the prop turns freely and start over.
Page 6
Global Water 800-876-1172 • globalw.com The Flow Probe uses true velocity averaging. When the average and maximum velocities are zeroed by pushing the top button, a running average is started. As long as the probe remains in the flow, the averaging continues.
Global Water 800-876-1172 • globalw.com V. Computer Operation a. The Flow Probe is calibrated at the factory. When you receive the product, you may wish to set the computer’s clock (see Computer Set- up), otherwise you should not have to alter any of your computer settings.
Protected Turbo-Prop propeller with electro-magnetic pickup. Weight: 2 Lbs (10 lbs. U.S., 14 lbs. international shipping weight) Size: Length: FP101 3' to 6'; FP201 5' to 15' Materials: PVC, anodized aluminum, stainless steel bearing Power: Internal watch type batteries/1 year life Operating Temperature: 0°...
Page 9
Global Water 800-876-1172 • globalw.com the back of the computer, ¼ turn to the left. Replace battery, + side toward battery cover, using a CR2032, 3 volt lithium cell. After replacing battery the calibration numbers will require resetting. (See Appendix A: Computer Setup) c.
Spin the propeller, by blowing on it, and check for an average reading. If there is still no reading contact Global Water. f. If the display becomes weak or does not light up at all, replace the battery.
Page 11
Clean and decontaminate the FP101/201 if necessary. Include a written statement describing the problems. Send the package with shipping prepaid to our factory address. Insure your shipment; Global Water’s warranty does not cover damage incurred during transit.
Global Water’s obligations under this warranty are limited to, at Global Water’s option: (I) replacing or (II) repairing; any products determined to be defective. In no case shall Global Water’s liability exceed the products original purchase price.
Global Water 800-876-1172 • globalw.com X. Appendix A: Computer Setup The BC1200 has the capability to switch between 2 different calibration factors. To change between the calibrations remove the computer from the flow probe head by twisting 45 degrees counter clockwise and lifting.
Page 14
Global Water 800-876-1172 • globalw.com (NOTE: after battery replacement and additional screen displaying SET ODO will follow the forth digit of the cal number. Ignore this and press the indented gray button to store settings) TO SET CLOCK • Press bottom button until clock appears at the bottom of the screen.