Copyright 1997 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company.
Read these instructions carefully. future reference. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Do not use this product near water. Do not place this product on an unstable cart, stand, or table.
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. 10. If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating.
14. Replace battery with the same type as the product's battery we recommend. Use of another battery may present a risk of fire or explosion. Refer battery replacement to a qualified serviceman. 15. Warning! Battery may explode if not handled properly. Do not recharge, disassemble or dispose of in fire.
DANGER INVISIBLE RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM. VORSICHT UNSICHTBARE LASERSTRAHLUNG WENN GEÖFFNET. NICHT IN DEN STRAHL SEHEN. ATTENTION RADIATION DU FAISCEAU LASER INVISIBLE. EN CAS D’OUVERTURE. EVITER TOUTE EXPOSITION AUX RAYONS. VARO AVATTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE ÄLÄ KATSO SÄTEESEEN. VARNING! OSYNLING LASERSTRÄLNING NÄR DENNA DEL ÄR ÖPPNAD.
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions. ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Léver det brugte batteri tilbage til leverandøren.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Purpose This user’s guide aims to give you all the necessary information to enable you to operate the system properly. Manual Structure This user’s guide consists of two chapters. Chapter 1 System Board This chapter describes the system board and all its major components.
Conventions The following are the conventions used in this manual: Text entered by user Screen messages , etc. Represents text input by the user. Denotes actual messages that appear on the screen. Represent the actual keys that you have to press on the keyboard. NOTE Gives bits and pieces of additional information related to the current...
Chapter 1 System Board Features...1-2 System Board Layout ...1-3 ESD Precautions ...1-4 Pre-installation Instructions...1-4 Pentium II Processor ...1-5 1.5.1 Installing a Pentium II Processor ...1-6 1.5.2 Removing a Pentium II Processor...1-8 Jumpers and Connectors ...1-9 Installing Memory...1-12 1.7.1 Installing a DIMM...1-19 1.7.2 Removing a DIMM...1-20 1.7.3...
Chapter 2 BIOS Utility Entering Setup ... 2-2 System Information ... 2-3 2.2.1 Processor... 2-4 2.2.2 Processor Speed ... 2-4 2.2.3 Internal Cache... 2-4 2.2.4 External Cache ... 2-5 2.2.5 Floppy Drive A ... 2-5 2.2.6 Floppy Drive B ... 2-5 2.2.7 IDE 1st Channel Master...
Basic Configuration...2-9 2.3.1 Date and Time ...2-10 2.3.2 Floppy Drives...2-11 2.3.3 IDE Drives ...2-11 2.3.4 Boot Options...2-15 Advanced Configuration ...2-18 2.4.1 Internal Cache (CPU Cache)...2-18 2.4.2 External Cache ...2-18 2.4.3 Cache Scheme ...2-19 2.4.4 Memory at 15MB-16MB Reserved For...2-19 2.4.5 Memory Parity Mode...2-19 2.4.6 C8000h-DFFFFh Shadow ...2-19...
List of Figures System Board Layout... 1-1 Installing the Retention Mechanism ... 1-6 Installing a Pentium II Processor ... 1-7 Removing a Pentium II Processor ... 1-8 Jumper and Connector Locations ... 1-9 CN12 - Reset Sw., Power Sw., and Turbo LED connector locations ...