RACOM MG102 Operating Manual
  1. Manuals
  2. Brands
  3. RACOM Manuals
  4. Network Router
  5. Midge MG102
  6. Operating manual

RACOM MG102 Operating Manual

Gprs/edge/umts router
Hide thumbs Also See for MG102:
Table of Contents

Advertisement

Quick Links

Download this manual
Operating manual
GPRS/EDGE/UMTS routers
1.1
12/17/2012
RACOM s.r.o. • Mirova 1283 • 592 31 Nove Mesto na Morave • Czech Republic
Tel.: +420 565 659 511 • Fax: +420 565 659 512 • E-mail: racom@racom.eu
.
MG102, M!DGE,
.
www.racom.eu

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MG102 and is the answer not in the manual?

Questions and answers

Related Manuals for RACOM MG102

Summary of Contents for RACOM MG102

  • Page 1 Operating manual MG102, M!DGE, GPRS/EDGE/UMTS routers 12/17/2012 RACOM s.r.o. • Mirova 1283 • 592 31 Nove Mesto na Morave • Czech Republic www.racom.eu Tel.: +420 565 659 511 • Fax: +420 565 659 512 • E-mail: racom@racom.eu...

  • Page 3: Table Of Contents

    2.2. Installation of the Router ....................15 2.3. GPRS/EDGE/UMTS router assembly ................16 3. Configuration ..........................17 3.1. Configuration via the M!DGE/MG102 Web Manager ............17 3.2. Configuration Parameters of the M!DGE/MG102 ............... 93 3.3. Configuration via Command Line Interface (CLI) ............. 106 4.
  • Page 4 A.2. Pin assignment COM interface RS485 ..................115 A.3. Pin assignment COM interface RS232 and RS485 ..............116 A.4. Pin assignment Ethernet Interface ................... 116 A.5. Pin assignment power plug ...................... 116 A.6. Pin assignment Ethernet Interface ................... 117 MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.

  • Page 5: Introduction

    Introduction Introduction Thank you for purchasing M!DGE/MG102 Wireless Router from Racom. This chapter gives you an in- troduction to M!DGE/MG102 Wireless Router. The following chapters describe the installation and the configuration. In next description is used the notation router instead of GPRS/EDGE/UMTS router.

  • Page 6: Product Description

    SIM card – works in two networks, WLAN no – N works in 850/900/1800/1900/2100 MHz bands, WLAN yes – W modem has an integrated GPS receiver Fig. 1.1: Production code MG102 MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.

  • Page 7: Product Description M!Dge

    Product description 1.2. Product Description M!DGE Fig. 1.2: Front panel and terminal panel of M!DGE The following table describes the meaning of the status indicators: © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 8 — Second Ethernet Port. Can be used as LAN or WAN Port — SMA female connector for GSM/UMTS antenna 50 Ω Please find the description of each interface in the following table: MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 9 Tab. 1.3: Pin assignment of screw terminal signal V1+ (12–48 V=) V2+ (12–48 V=) Out1: Dry contact relay Normally open with M!DGE without powering Out2: Dry contact relay Normally open with M!DGE without powering DI1− DI1+ DI2− DI2+ © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...

  • Page 10: Product Description Mg102

    The front panel has 10 status indicators. In addition there are two SIM card slots and a reset button at the front panel. Fig. 1.3: The Front Panel The following table describes the components on the front panel: MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.

  • Page 11: Components On The Front Panel

    Restart: press this button when the status LED is on Front Reset – – Factory reset: press and hold this button for at least 5 seconds Front SIM1 – – SIM socket 1 Front SIM2 – – SIM socket 2 © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...

  • Page 12: The Back Panel Of 2009 Model

    Voltage feed connector (9–32 VDC) Physical link Link/Activity Back green No physical link (Ethernet Ports) flashing Data transmission Data rate 100 MBit/s Speed 10/100 Back green (Ethernet Ports) Data rate 10 MBit/s MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.

  • Page 13: M!Dge/Mg102 Software

    ○ Over the air software update 1.5. Application Overview M!DGE/MG102 is an access router for mobile telecom networks. Router can hook up a whole local area network to the mobile telecom network. Certainly M!DGE/MG102 can also be used to attach a single device.
  • Page 14 General Packet Radio Service (GPRS), Enhanced Data rates for GSM Evolution (EDGE) • Circuit Switched Data (CSD) 1.5.2. Access to a Remote Network M!DGE/MG102 can be used to access a remote network. Possible setups are: • Access via public IP address •...

  • Page 15: Installation

    2.2. Installation of the Router MG102 is designed for mounting to a panel using through holes or to be put on a worktop for installing to DIN rails use DIN rail bracket. M!DGE is designed for mounting to a DIN rail. Please consider the safety instructions and the environmental conditions.

  • Page 16: Gprs/Edge/Umts Router Assembly

    MG102 can be powered with the included power supply or another external source supplying between 9 and 32 Volts DC (10–55 Volts DC M!DGE). M!DGE/MG102 is for use with certified (CSA or equivalent) power supply, which must have a limited and SELV circuit output.

  • Page 17: Configuration

    • M!DGE can be configured via a USB stick with a prepared configuration file. If you are new to M!DGE/MG102 we recommend configuring it using the M!DGE/MG102 Web Manager. 3.1. Configuration via the M!DGE/MG102 Web Manager The M!DGE/MG102 Web Manager can always be reached via the Ethernet interface. After the successful setup the Web Manager can also be accessed via the mobile interface.
  • Page 18 If not yet enabled, please enable the Dynamic Host Configuration Protocol (DHCP) so that your computer can lease an IP address from M!DGE/MG102. Wait a moment until your PC has re- ceived the parameters (IP address, subnet mask, default gateway, DNS server).
  • Page 19 Configuration 3.1.3. Home This page gives you a system overview. It helps you when initially setting up device but also functions as dashboard during normal operation. © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 20 Configuration 3.1.4. Interfaces In the section the physical Interfaces of M!DGE/MG102 are configured. Details for all enabled connec- tions are displayed on its own section Appendix A, Connectors and Cables • Link Management FW 3.4 introduces a WAN link manager. Depending on your hardware, you can choose from Mobile (GSM/UMTS), WLAN, Ethernet and PPPoE.
  • Page 21 • Link Management – Setings IP health check – this feature is prepared for switching between profiles or lines. MG102 is checking availability of Monitored host 1 (optionaly 2). If the host (hosts) is (are) not reachable the second profile (link) will be switched to.
  • Page 22 Ethernet Interface • Switch Settings Choose whether you want to have all Ethernet ports in one LAN (default) or apply a subnet for every Ethernet port or have a WAN port separated. MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 23 Port 2 192.168.2.0/24 192.168.2.1 Port 3 192.168.3.0/24 192.168.3.1 Port 4 192.168.4.0/24 192.168.4.1 • Port Settings For every Ethernet port the link negotiation can be set. In most cases auto negotiation will work. © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 24 • IP Settings Define the M!DGE/MG102 LAN. Usually the first address within that LAN is assigned to the router. Provide that IP address and net mask in dot-decimal notation or use the defaults. MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 25 Access con- centrator This may be left blank and the client will connect to any access concentrator. name: © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 26 ‘dial on demand’ Operational connection Shows whether a connection is up or not. status: Application area: Choose mobile if M!DGE/MG102 is driving around. For stationary installa- tion choose ‘stationary’ Service type: The preferred service type can be set here. IP address:...
  • Page 27 PPP DNS Specifies whether a DNS request to the provider is made or not. query: Enable Specif- ic Client IP Ad- Enable or disable fixed IP address on the mobile interface. dress: © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 28 Maximum Segment Size (MSS) described above Maximum Segment Size • This section lets you store the PIN code. With the correct PIN code deposited you will be able to enable or disable PIN protection. MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 29 Configuration M!DGE/MG102 can only read SIM cards if the correct PIN code is provided or if PIN protection is disabled. It is not recommended to disable PIN protection since a SIM card thief could misuse an unprotected SIM. Parameter Description PIN code: The PIN code for the SIM card.
  • Page 30 Hardware flow In RTS/CTS hardware flow control, the computer and the modem use the RTS and control: CTS lines respectively to control the flow of data USB Port valid only for M!DGE MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 31 Enable USB autorun feature. Digital I/O Server (M!DGE only) • Digital I/O Management via Web Manager The digital inputs and outputs can be monitored and controlled via the Web Manager or by software. © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 32 ○ Get status of digital inputs and output To get the states of the digital I/O send the following pattern as ASCII characters Pattern Description 00010000 Request a message with all states MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 33 Identity of network interface through which a packet will be sent to reach the gateway. The 'distance' to the target (usually counted in hops). It is not used by recent kernels, Metric but may be needed by routing daemons. © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 34 3.1.6. Firewall Access Control Lists • Access Control for Local Host – The access from the WAN interface to M!DGE/MG102 itself and its local applications can be managed using this filter. • Access Control for Exposed Host from WAN and OpenVPN – The access from the WAN interface to a defined Exposed Host can be managed using this filter.
  • Page 35 VPN tunnel or the WAN interface to get direct Internet access. Note Filtering for LAN interfaces is available only if 4LANs are set in Interfaces Switch setings Ethernet Mode. © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 36 Host to which the traffic will be forwarded. Internal port: Port to which the traffic will be forwarded. Protocol: Protocol (UDP or TCP) to which this entry applies. Enabled: Enable (Yes) or disable (No) the entry. MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 37 Configuration • NAPT on OpenVPN Interface The same settings as above, but for other interface Expert Mode Upload text files with firewall rules. © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 38 A Guide to basic RSA Key Management is found under http://openvpn.net/easyrsa.html For alternative authentication methods see http://openvpn.net/index.php/documentation/howto.html#auth For more information also see http://openvpn.net/howto.html Please make sure that the M!DGE/MG102 system time is correct when working with OpenVPN. Other- wise authentication issues may arise. •...
  • Page 39 Second OpenVPN server address (optional) Second server port Second OpenVPN server port (optional) VPN device type tun or tap Bridging With tap: bridge tap device with ethernet, or use routing Compression Enable or disable OpenVPN compression © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 40 If OpenVPN is enabled and the configuration mode is set to “client expert configuration” all configurations (*.conf) will be started after mobile connection establishment. MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 41 Configuration OpenVPN Configuration (Server Expert Configuration) This configuration mode lets you run an OpenVPN server on M!DGE/MG102. The configuration upload takes a zip file which may include one or more OpenVPN server configurations. Typically such a zip file includes files such as: •...
  • Page 42 Configuration • IPsec Administration Parameter Description IPsec administrative status: Enable or disable IPsec. • IPsec Configuration MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 43 Configuration © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 44 (R_U_THERE, R_U_THERE_ACK) that are sent for this connection (default 30 [sec]: seconds). The number of unanswered DPD R_U_THERE requests until the IPsec peer is Failure count: considered dead (M!DGE/MG102 will try to reestablish a dead connection automat- ically) MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 45 “User Accounts”. Parameter Description PPTP state Enable/disable PPTP server PPTP address range start: Address range start for PPTP server PPTP address range size: Address range size for PPTP server Dial-in Server © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 46 Configuration On this page the Dial-in server of M!DGE/MG102 can be administrated and configured. Users that are allowed to dial-in are defined under the section “User Accounts”. • Dial-in Server Administration Parameter Description Dial-in administrative The Dial-in server can be enabled or disabled. Consequently the device status: will allow incoming calls or not.
  • Page 47 Max Packet Timeout: If data is received on serial line, waits for more data for the configured time to avoid to much segmentation which would lead on inefficiency • Max Latency Timeout: Limits the maximum latency if the above criteria are not fulfilled © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 48 The protocol implicitely defined on the COM port. Time-out TCP – timeout in seconds or endless • UDP Configuration Parameter Description Local Port Local UDP port Remote IP IP address of remote MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 49 Second the active connection should be monitored. If you are running an IPsec or OpenVPN based VPN we recommend to use the protocol integrated monitoring service (IPsec DPD or OpenVPN keep- alive). Else you should configure and enable the ping monitor application. © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 50 If both Host1 and Host2 are not available the restarting with primary profile will follow. In case that IP health check is set for longer period that Ping monitor for internal switch to the fallback profile will NEVER be proceded. MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 51 The DHCP server assigns the following information: Any IP address out of the configured range As default gateway the IP address of M!DGE/MG102 is assigned As DNS server the IP address of M!DGE/MG102 is assigned or manually configured DNS servers • DHCP Server Administration...
  • Page 52 Propagate DNS proxy server as third DNS server DNS Proxy Server The DNS Proxy enabled M!DGE/MG102 forwards DNS requests to the DNS server provided by the mobile operator. Devices within the M!DGE/MG102 LAN may be configured to use M!DGE/MG102 as DNS server.
  • Page 53 Configuration Dynamic DNS The Dynamic DNS Client of M!DGE/MG102 is completely compatible to the Dynamic Network Services provided by the organization DynDNS (www.dyndns.com). • Dynamic DNS Administration Parameter Description Dynamic DNS status: Enable or disable the Dynamic DNS Client •...
  • Page 54 Description From e-mail address: Sender’s e-mail address Server address: SMTP server address Server port: Default port for SMTP is 25 If enabled M!DGE/MG102 will logon to SMTP server before sending Authentication required: e-mails User name: Username Password: Password MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 55 VPN connection failure VPN failure to connect. See logs to identify the problem. Dial-in connection estab- Dial-in connection establish: user: %DIN_USER% from: %DIN_IP%. lished Dial-in connection down Dial-in connection terminated: user: %DIN_USER% from: %DIN_IP%. © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 56 %LOGIN_USER% Name of the user who tried to log on to the Web Manager %DIO_SOURCE% Source that triggered an output change %UDP_MESSAGE% Text message that has been received by the message receiver MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 57 Subscribers are recepients of SMS or e-mail event notifications. It is possible to create groups and fill them with users and other groups. This mechanism let you send event notifications to multiple destinations/users. © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 58 Notifications can be generated or digital outputs can be set based on the occurrence of several events. This feature is available on MG102xGx (a valid GPS license is required). • GPS Settings GPS Settings menu allows enabling of GPS and setting of operational mode: MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 59 ○ Serve with Berlios daemon The Berlios daemon will be started in the MG102 unit. With this setting the Show location will work and information about position, altitude and number of available satellites in GPS Data submenu will be available. The default TCP port of Berlios daemon is 2947.
  • Page 60 $GPVTG, $GPGSV and $PNMID will be used. Destination address and UDP port has to be set up. The data will be send out in setted update cycle [seconds]. ○ Output to local COM port MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 61 Both UDP and COM interface will be used in the same time as mentioned above. Following NMEA sentences are used with UDP or COM interface: RMC–Recommendet Minimum Specific GNSS Data Example 3.1. RMC data format $GPRMC,075738.0,A,4934.105405,N,01604.635656,E,0.0,26.9,250512,,,A*55 © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 62 Satellite Used Sv on Channel 2 Satellite Used Sv on Channel 12 PDOP Position Dilution of Precision HDOP Horizontal Dilution of Precision VDOP Vertical Dilution of Precision Checksum <CR><LF> End fo message termination MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 63 A valid position fix indicator is derived from the SiRF Binary M.I.D. 2 position mode 1. See the SiRF Binary Reference manual. VTG–Course Over Ground and Ground Speed Example 3.4. VTG data format $GPVTG,26.9,T,26.9,M,0.0,N,0.0,K,A*23 © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 64 Elevation degrees Channel 4 (Maximum 90) Azimuth degrees Channel 4 (True, Range 0 to 359) SNR (C/No) dBHz Range 0 to 99, null when not tracking Checksum <CR><LF> End fo message termination MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 65 WLAN is available only with MG102-2xW hardware. • WLAN is available only with MG102-2xW hardware WLAN is enabled or disabled on this page; on the same page is available Operational Connection Status. © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 66 The WLAN interface can be operated in client or access point mode. In client mode it will be an additional WAN link, in access point mode it will serve as WLAN access point. MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 67 Configuration If you configure WLAN as a Access point you have to set SSID, Chanel number used, Authentific- ation mode and the Preshared key. • WLAN Network List © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 68 Configuration Please wait a while, MG102 will scan all available networks. You can choose one item from this list using Use button, then you will be redirected to Administration window [WLAN configuration] • National Restrictions This product may be used in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: ○...
  • Page 69 3000 m Permitted to use on board aircraft during a flight at the 5650-5825 100 mW (20 dBm) altitude not less than 3000 m http://www.comunicazioni.it/ © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 70 ○ Turkey Frequency Range Restrictions 5470-5725 MHz Not implemented SMS can be used to control M!DGE/MG102 and for event notification. Parameter Description Sending SMS can be enabled or disabled. Disabling sending SMS means that SMS notification: no notification via SMS will be performed.
  • Page 71 Set administrative status of the mobile connection to enabled, dial on dialondemand demand. 1 on Switch output 1 on 1 off Switch output 1 off output 2 on Switch output 1 on 2 off Switch output 2 off © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 72 SSH Server Parameter Description Port: SSH server port The standard port 22 is used. For higher security change it to different number. This number shall be used as parametr in SSH command. MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 73 No further traps will be sent as long signal strengt his not higher than this. ivation threshold dBm: Operation mode SNMP version. SNMP traps are generated in the following situations, if the SNMP agent is enabled: © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 74 The system-shutdown trap is sent, when the system is rebooted via the reboot function of the web in- terface or when the watchdog reboots the system. Telnet Server Parameter Description Port: Telnet server port MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 75 UDP packets with a string in the payload. If an UPD package is arriving, the event “Arriving UDP Message” is fired (see chapter ???). Use the Event Manager (the section called “Event Manager”) to forward the message (UDP payload) to a SMS or E-mail destination. © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 76 GSM Network. A sample USSD service is the bill status service accessed by dialing *141# or similar numbers in between * and # ac- cording to mobile network. Contact your mobile operator for further information. MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 77 Configuration Web Server Parameter Description HTTP port: Web server port for http connections HTTPS port: Web server port for https connections © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 78 Be carefull with DHCP server used together with redundancy. If you use activated DHCP server, you have to split the DHCP range between Master and Backup (e.g. 192.168.1.100- 150 on the master and 192.168.151-199 on the backup) MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 79 Define whether user must accept by pressing a button or they have to au- Authentication Mode: thenticate to a RADUIS server. Walled Garden Address: Requests to this address are not being checked. © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 80 Configuration 3.1.9. System Authentication MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 81 Confirm the password File Configuration Configuration via the Web Manager becomes tedious for large volumes of devices. M!DGE/MG102 offers automatic and manual file-based configuration. A single text file (*.cfg) or a zip archive (*.zip) containing one or more of the following files can be up- loaded.
  • Page 82 Description Status: Enable/disable automatic configuration update Time of day: Every day at this time M!DGE/MG102 will do a check for updates Mode: Update over mobile or Ethernet Interface? Specify the protocol used to transfer the new user configuration file to Protocol: M!DGE/MG102.
  • Page 83 The following files are acceppted for upload: • *.cfg (max size 100KB) • *.zip (max size 100KB) The zip file may include New configuration • user-config.cfg files: • ca.crt.credential_mode • ca.crt.certificate_mode • client.crt.certificate_mode • client.key.certificate_mode • templateProfiles © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 84 This action can also be initiated by pressing and holding the Reset button for at least five seconds. The factory reset will also set the IP address of the Ethernet interface to 192.168.1.1. You will be able to communicate again with the device using the default network parameters. MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 85 Configuration Troubleshooting • Network Debugging © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 86 Configuration • Log Files Log files can be viewed a downloaded here. Please provide these files when placing a support re- quest. • System Log Redirection MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 87 The host where the syslog messages will be forwarded to. IP address: A Syslog server has to be running on this IP address. You can use free TFTP server TFTPD32 for example. • Restart • Tech Support © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 88 Configuration Note For using of this feature a connection to Internet is required. • System Information: Provide this information when placing a support request. MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 89 Time and Region The Network Time Protocol (NTP) is a protocol for synchronizing the clocks of computer systems over packet-switched, variable-latency data networks. M!DGE/MG102 can synchronize its system time with a NTP server. If enabled, time synchronisation is done after the mobile interface is up but before starting any VPN connections.
  • Page 90 • Manual Software Update The easiest way to update the M!DGE/MG102 Software is to connect M!DGE/MG102 to network with a TFTP server. If you only have a Notebook or a PC available the update process involves the preparation of a TFTP Server.
  • Page 91 Parameter Description Mode: Update over mobile or Ethernet Interface? Specify the protocol used to transfer the new software to M!DGE/MG102. Protocol: You will need an appropriate server. Server IP address and Provide a host name and a path to a server which hosts the new software.
  • Page 92 Check the results of the update. Refreshing the page or even reopening the browser windows may avoid cache problem. In case of success, “software update successfull” will be displayed, otherwise an error message. MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.

  • Page 93: Configuration Parameters Of The M!Dge/Mg102

    3.2. Configuration Parameters of the M!DGE/MG102 The information in this chapter is needed to configure M!DGE/MG102 via the Command Line Interface or File Configuration. If you are using the Web Manager and its forms to configure M!DGE/MG102, you may skip this chapter.
  • Page 94 Configuration Racom has defined some types of parameters that are often used. The table below shows the defined parameter types. In addition other types of parameters may exist. Parameter Type Allowed charac- Format Description ters a–z A–Z String must include “@”...
  • Page 95 Profile name dialout.profiles.1.username void username Username dialout.profiles.1.password void password Password dialout.pro- void phone number Phone number files.1.phoneNumber dialout.profiles.1.authMeth- Chap = CHAP void [chap, pap] Pap = PAP © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 96 0 = set values after reboot to digitalIO.afterReboot.output1 digitalIO.keepOnReboot [0,1] digitalIO.afterReboot.output2 1 = restore values after reboot digitalIO.afterReboot.output1 [on,off] State of output 1 after reboot digitalIO.afterReboot.output2 [on,off] State of output 2 after reboot MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 97 [1 .. 65535] Internal port [0..49] napt_mobile.<j>.protocol [TCP, UDP] TCP or UDP 0 = disabled napt_mobile.<j>.status [0,1] 1= enabled 0 = redirect to other host napt_mobile.<j>.isRedirect [0,1] 1 = redirect to localhost © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 98 [0,1,2] 1 = permit entries 0 = permit all firewall_exposed_host_mobile.host void hostname The exposed host firewall_exposed_host_mo- void hostname Source host / net bile.<j>.target with j = [0..19] firewall_exposed_host_mo- void netmask bile.<j>.mask MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 99 For credential-based authentication IPsec Parameters Parameter Default Value Range Description 0 = disabled ipsec.status [0,1] 1= enabled ipsec.remote.serverIp void ipaddress 0 = crertificate-based authentication ipsec.remote.lanAddress void Ipaddress 1= credential-based authentication © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 100 0 = Dial-in disabled dialin.status [0,1] 1= Dial-in enabled dialin.configuration.address- 192.168.254.1 ipaddress Address range start RangeStart dialin.configuration.address- [2..254] Address range size RangeSize 0 = off dialin.disableNapt [0,1] 1= Disable NAPT on Dial-on MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 101 1= DHCP server on network.DHCPSettings.AddressRange- 192.168.1.100 ipaddress DHCP range start Start network.DHCPSettings.AddressRangeS- [1..255] DHCP range size network.DHCPSettings.DNSServer Proxy hostname DNS Server 1 network.DHCPSettings.DNSServer0 void hostname DNS Server 2 network.DHCPSettings.DNSServer1 void hostname DNS Server 3 © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 102 1= enabled email.sending.smtp.host void hostname email.sending.smtp.port void [1 .. 65535] email.sending.smtp.from void email From E-mail Address email.sending.smtp.authen- 0 = disabled void [0,1] tication 1= enabled email.sending.smtp.user- void username name email.sending.smtp.pass- void password word MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 103 Event Message events.digitalOutput2_On.message void password Event Message events.digitalOutput1_Off.message void password Event Message events.digitalOutput2_Off.message void password Event Message events.udpMessage.message void password Event Message events.gpsUp.message void password Event Message events.gpsDown.message void password Event Message © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 104 [1 .. 65535] snmp.siglow -113 [-113 to -51] Signal strength trap threshold dBm Signal strength trap reactivation snmp.sighigh [-113 to -51] threshold dBm: MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 105 0 = disabled administrator.deviceAccess [0,1] 1= enabled user.<k>.name void hostname with k = [0..20] user.<k>.password void password Troubleshooting Parameter Default Value Range Description redirectSyslogIp void ipaddress 0 = disabled webMgrDbg.status [0,1] 1= enabled © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...

  • Page 106: Configuration Via Command Line Interface (Cli)

    3.3. Configuration via Command Line Interface (CLI) The command line interface is accessible after successful login to M!DGE/MG102 via telnet or Secure Shell (SSH). By default the telnet server answers on port 23, the SSH server on port 22.
  • Page 107 CLI will stop after every call. You have to include ‘cli’ for every new call. 3.3.1. CLI Overview The Command Line Interface mainly provides functions to read and write values of the M!DGE/MG102 configuration parameters. In addition, the CLI provides functions to query status information.
  • Page 108 ‘cli select automatic’ and ‘cli select automatic sim1’ The following commands have the same effect: ‘cli select automatic sim1’ and ‘cli set networkselec- tion.mode=automatic’ ‘cli select automatic sim2’ and ‘cli set networkselec- tion.sim2.mode=automatic’ MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 109 NAPT service on the mobile if napt_state_mob © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...
  • Page 110 M!DGE/MG102 CPU cli status system wireless_module show the M!DGE/MG102 wireless module cli status system ram show the amount of RAM installed in the M!DGE/MG102 cli status system flash show the amount of flash installed in the M!DGE/MG102 Help Print the cli help message (usage) MG102, M!DGE, GPRS/EDGE/UMTS routers –...
  • Page 111 Configuration Command Usage and Return Value Exit Not for end user use! Root rights are required. © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...

  • Page 112: Troubleshooting

    4.2. System Log and Log Files Find more information about troubleshooting tools. The Web Manager provides various debugging tools under SYSTEM/Troubleshooting: 4.3. Network Protocol Analyzer Via the Linux Shell (bash), the protocol analyzer “tcpdump” is available: MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 113 Troubleshooting © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...

  • Page 114: Customer Service

    Customer Service 5. Customer Service 5.1. Support Please send questions or comments about M!DGE/MG102 to: support@racom.eu MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.

  • Page 115: Connectors And Cables

    COM – RS485 signal In/ Out — — — — 3 (M!DGE) RxD/TxD+ — — — — — — RxD/TxD− 9(MG102) RxD/TxD+ Note Do not use pins that are not listed here! © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...

  • Page 116: Ethernet Plug (Eth; Rj-45)

    Socket and 100BaseT) signal TX− RX− Fig. A.3: RJ-45 Plug A.3. Power Plug MG102 Tab. A.5: Pin assignment power plug MSTB 2,5/ 2-ST-5,08 Power (Phoenix Contact) signal − Fig. A.4: Power connector MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.

  • Page 117: Cable Eth/Rs232

    Connectors and Cables A.4. Cable ETH/RS232 Tab. A.6: Pin assignment Ethernet Interface ETH RJ-45 RS232 D-SUB-9 signal In/ Out Fig. A.5: RJ-45 and RS232 D-SUB-9 © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...

  • Page 118: Safety Instructions

    The M!DGE/MG102 Wireless Routers must not be opened. Only the replacement of the SIM card is permitted. Voltage at all connectors of the communication module is limited to SELV (Safety Extra Low Voltage) and must not be exceeded.

  • Page 119: Rohs And Weee Compliance

    In accordance with the requirements of the counsil directive 2002/96/EC on Waste Electronical and Electronic Equipment (WEEE), ensure that at end-of-life you separate this product from other waste and scrap and deliver it to the WEEE collection system in your country for recycling. © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...

  • Page 120: Glossary

    Internet Protocol Security ISDN Integrated Services Digital Network Internet Service Provider Local Area Network NAPT Network Address Port Translation Network Address Translation Point of Presence POP, POP3 Post Office Protocol, Version 3 http://www.ce.org MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.
  • Page 121 Subscriber Identity Module Software Transmission Control Protocol TFTP Trivial File Transfer Protocol User Datagram Protocol UMTS Universal Mobile Telecommunications System Universal Resource Locator Virtual Private Network WEEE Waste Electrical and Electronic Equipment) environmental directives © RACOM s.r.o. – MG102, M!DGE, GPRS/EDGE/UMTS routers...

  • Page 122: Revision History

    Revision History Appendix D. Revision History Revision 1.1 2011-11-01 1. XML version MG102, M!DGE, GPRS/EDGE/UMTS routers – © RACOM s.r.o.

This manual is also suitable for:

M!dge

Table of Contents