Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ocean Rodeo SHIFT GEN 3
Summary of Contents for Ocean Rodeo SHIFT GEN 3
- Page 1 SHIFT GEN 3 / PILOT GEN 2 User Manual...
-
Page 3: Table Of Contents
SHIFT GEN / PILOT GEN User Manual TABLE OF CONTENTS WARRANTY........................SAFETY PRECAUTIONS....................SHIFT FEATURES......................PILOT FEATURES......................PIGTAIL GUIDE......................GEN 9 PUNCHOUT TRIM LOOP................TRIM LOOP RELEASE CUFF ACTIVATION............... TRIM LOOP RESET....................... USING THE LOCK IN TUBE..................QUICK CHANGE TRIM LOOP..................BELOW BAR SWIVEL .................... -
Page 4: Warranty
All kite control bars are covered by a one year warranty offered to the original purchaser on workmanship and materials. Warranty is limited to the repair or replacement at Ocean Rodeo’s sole discretion. This warranty does not cover damage caused by normal wear and tear, misuse or negligence and does not extend to any other equipment possibly damaged in the event of a product failure. - Page 5 SHIFT GEN / PILOT GEN User Manual � Before launching your kite at an unfamiliar location, scout for safety hazards and consult other kiters in the area for possible concerns (rocks, reefs, currents, changeable weather, local ‘best practices’, etc). � Never launch with obstacles or people closer than two full line lengths downwind.
-
Page 7: Shift Features
SHIFT GEN / PILOT GEN User Manual SHIFT FEATURES ......I3 LINE SPLITTER ....PUSH AWAY KITE LEASH RELEASE CUFF ......BACK FLYING LINES ..... STAINLESS CLIP WITH ..FORCE TENSIONER SPRING CAP RETRACTABLE COVER ..I3 FORCE TENSIONER SYSTEM ...... -
Page 9: Pilot Features
SHIFT GEN / PILOT GEN User Manual PILOT FEATURES ......FRONT FLYING LINES ....LEASH ATTACHMENT RING ......BACK FLYING LINES ...........TRIM LOOP ..........PULLEY ........LOCK IN TUBE ..SINGLE FRONT LINE RE-RIDE ....PUSH AWAY KITE LEASH RELEASE CUFF ......BACK LINE LEADERS ..... STAINLESS CLIP WITH .........TRIM CLEAT RETRACTABLE COVER ......VELCRO TRIM HANDLE... -
Page 10: Pigtail Guide
PIGTAIL GUIDE Warning: Before riding with your new Ocean Rodeo Shift bar, please ensure you are using the appropriate pigtails and that your kite is properly rigged. Included with this bar you have received: 2 x 20cm front line pigtails (A) -
Page 11: Gen 9 Punchout Trim Loop
SHIFT GEN / PILOT GEN User Manual GEN 9 PUNCHOUT TRIM LOOP Your Gen 3 Shift bar features the ISO compliant Gen 9 Punchout trim loop. Designers Tip: The push release cuff has a lip for improved grip on one side and is smooth on the opposite side. -
Page 12: Trim Loop Release Cuff Activation
TRIM LOOP RELEASE CUFF ACTIVATION Note: Always test your quick release before each session and always flush release after each session! To separate yourself from the trim loop in an emergency situation, push the release cuff away from you. As long as your kite leash is attached to the flagout ring, the control bar will ride up a single front line and depower the kite. -
Page 13: Trim Loop Reset
SHIFT GEN / PILOT GEN User Manual TRIM LOOP RESET To reset your trim loop after it has been released: � Begin by locking the cuff in the UP position if it is not already. To do this hold the trim loop system in an upright position and push up on the cuff. �... -
Page 14: Using The Lock In Tube
USING THE LOCK-IN TUBE The lock-in tube helps keep your trim loop hooked in if you have slack or minimal tension on your lines while riding. To use the lock-in tube, simply flex the tubing into the head of the harness, under the trim loop. QUICK CHANGE TRIM LOOP The trim loop can easily be replaced or switched out in favor of Ocean Rodeo’s Slider or Freestyle loops. - Page 15 SHIFT GEN / PILOT GEN User Manual Slider Loop Freestyle Loop Note: Slider loop must be used with correctly sized ring on the harness rope to ensure clean release. Refer to manual supplied with slider loop for most recent information.
-
Page 16: Below Bar Swivel
BELOW BAR SWIVEL Twisted front lines can affect the operation of your front line flagout depower system. To correct twisted front lines: Grasp the swivel head and turn it in the opposite direction of the line twists. WARNING: Multiple twists in your front lines can create dangerous amounts of friction and prevent proper depowering when the front line flagout system is activated. -
Page 17: Leash To Line Attachment
SHIFT GEN / PILOT GEN User Manual LEASH TO CENTRE LINE ATTACHMENT To attach the leash to the trim loop slide the EVA float back to expose the clip and clip it onto the flagout rig as shown below. Designer Tips: Once clipped onto the flagout ring, slide the float back up to cover the clip opening. -
Page 18: Leash To Harness Attachment
LEASH TO HARNESS ATTACHMENT Note: Always attach your leash with the release cuff end closest to your harness! Remove the connection tether from the leash and attach it to the harness ring, as shown below. - Page 19 SHIFT GEN / PILOT GEN User Manual Once the connector tether has been attached to your harness, reset the leash’s quick release following the steps shown below.
-
Page 20: Release Cuff Maintenance
RELEASE CUFF MAINTENANCE Note: Always flush sand and debris out your release systems after each session. -
Page 21: Single Front Line Flagout Depower
(This can not be done while lines are wrapped around the bar.) For information on replacing a damaged front flagout line contact your ocean rodeo dealer or visit oceanrodeo.com/support... -
Page 22: Using The I3 Sidewinder (Shift)
USING THE I3 SIDEWINDER (SHIFT) NOTE: While riding, the I3 Sidewinder should be located on your right side. To add power: Twist the tuning knob clockwise (1). The winder will add ½ cm of trim for every quarter turn of the knob. To depower: Bump or nudge the tuning knob outwards to allow the winder to unspool the wound up trim line in a controlled manner (2). - Page 23 SHIFT GEN / PILOT GEN User Manual When the bar is at minimum power, a second white marker will become visible at the top of the float (1). When the bar is wound to mid power, the first white marker will centered in the window on the tension lock (2).
-
Page 24: Tuning The Lines (Shift)
TUNING THE LINES (SHIFT) Your kite’s performance relies on properly tuned lines! Make a habit of checking your line lengths regularly. Attach all four lines to a solid object (fence, line wrapped around a tree, etc.) Pick up the kite bar and make sure the winder is set for maximum power before tuning your lines. - Page 25 SHIFT GEN / PILOT GEN User Manual 2. If the difference between line lengths is large (>2cm), you should adjust line lengths using your pigtails. See the Pigtail Guide on the following pages. If the springs are not equally compressed when fully powered, the trimline has stretched and must be adjusted at the winder.
-
Page 26: Using The I3 G-Stop (Shift)
USING THE I3 G-STOP (SHIFT) To adjust the stopper position on the locking tube, align the top edges of both stopper components . To lock the stopper in place, tap it with your control bar. This will offset the two stopper components and engage the friction pad locking mechanism. Warning: Do not move stopper below safe-line marked on locking tube. -
Page 27: The I3 Force Tensioner System (Shift)
SHIFT GEN / PILOT GEN User Manual THE I3 FORCE TENSIONER SYSTEM (SHIFT) The tensioning system allows the user to depower their kite when there is no tension on the back lines. To keep the tensioning system free from sand and debris, rinse it regularly. -
Page 28: Bar Trim Adjustment (Pilot)
BAR TRIM ADJUSTMENT (PILOT) � Bar is set at maximum power when trim line is in longest position. � To depower the kite, pull down on Velcro trim handle. � To add power to the kite, pull down and away from the cleat to disengage. -
Page 29: Storing And Caring
SHIFT GEN / PILOT GEN User Manual STORING AND CARING For smooth operation; if your bar is covered with sand or debris, give it a quick rinse in the water before and after riding. To avoid tangles, we suggest you wind your lines in a figure 8 pattern around your bar ends. - Page 30 Use bar end line bungees to secure your kite lines for tangle free storage. Thoroughly rinse with fresh water after each session and store out of direct sunlight. WARNING! Knots can easily form in your flying lines, especially close to the kite end of your lines. Always inspect for and remove knots when found.
-
Page 31: Iso Compliance
/ PILOT GEN User Manual ISO COMPLIANCE Ocean Rodeo has worked closely with The GKA on introducing a new ISO safety standard for quick-release systems on kite bars. The new ISO standard regulates how bars are tested to ensure a level of safety you can rely on even in the harshest conditions. - Page 32 oceanrodeo.com info@oceanrodeo.com NA Toll Free 1-888-544-4969 INT +1 (778) 734-2696...