TABLE OF CONTENTS PACKAGE
C ONTENTS....................3
PRODUCT
D ESCRIPTION ....................3
SPECIFICATIONS ......................3
INSTALLATION
A ND
O PERATION ..................4
UNPACKING
a nd
H ANDLING ........................4 MECHANICAL
I NSPECTION.......................... 4 ...
One 12VDC 2A power supply One user manual PRODUCT DESCRIPTION The ST-PTZMINI-KB is a professional grade pan, tilt, zoom (PTZ) controller for up to 31 PTZ-enabled CCTV cameras and other devices. The unit uses RS-485 communications, includes an LCD display and a 3-axis joystick.
Using an AC or other incorrect power supply will damage the unit. g. Only qualified installers are allowed to install and test the ST-PTZMINI-KB. h. As the ST-PTZMINI-KB is a sensitive device any shock or collision to the unit or shaking of the unit will cause damage and void the warranty.
Page 5
LCD screen. Note: When the controller is initializing the joystick should be in the “nil” (0 or neutral) position. e. It is also possible for the ST-PTZMINI-KB to control multiple PTZ cameras using a matrix switch in lieu of a DVR per the diagram below. The PTZ controller and cameras are connected in parallel to the matrix’s RS485 buss.
Controller Matrix PTZ Camera 1 PTZ Camera 2 Note: If using more than one PTZ controller each controller must have a unique ID. Further, no more than 4 ST-PTZMINI-KBs can be used in one system. 5. KEYBOARD
O PERATION
LCD Screen Lens Control 3D Joystick...
Camera Address: To choose the camera to operate use N + CAM where N is the camera address (e.g., 1). Enter camera address then press CAM. PTZ Camera Lens Control: Use the ST-PTZMINI-KB to control the camera’s Zoom, Focus and Iris lens features.
Page 8
Matrix Control: A matrix can support a specific number of PTZ cameras. The ST-PTZMINI-KB can support up to 16 PTZ cameras in a matrix. All camera information such as address, data, and time will be displayed when switching from one camera to another.
KEYBOARD
M ENU
C ONTROL:
Parameter
S etup
Joystick
C alibration
Camera
S etup
Camera
S can
S etup
Camera
P attern
S etup
Camera
...
Page 10
Keyboard Baud Rate Setting: Press the MENU key and select 1. Keyboard Setup from the main menu. The Keyboard Setup Menu screen similar to the one below will appear. 1. Set KB ID (1-64): 2. Set Baudrate: 2400bps 3. Joy Calibrate 4.
Page 11
1. Set KB ID (1-64): 2. Set Baudrate: 2400bps 3. Joy Calibrate 4. About Keyboard Press the 3 key. The LCD will display: Joystick is free then press ENTER Press ENTER and the joystick calibration is completed. The LCD will display “Success”.
Page 12
Preset num:________ (1-128) Press PREV to back Press PREV to return to the previous menu. To show a preset, press the 2 key for Show Preset under the Dome Setup Menu. Preset num:________ (1-128) Press PREV to back Input the preset number and press ENTER to call it. The LCD will then display “Success”.
Page 13
Scan Setup: Enter the Dome Setup Menu and press the 2 key for Set Dome Scan. The LCD will display: 1. Set Left Limit 2. Set Right Limit 3. Run Scan To set the left limit, press 1. Set Left Limit and press ENTER to enable the joystick.
Page 14
Tour Setup: Enter the Dome Setup Menu and press the 4 key for Set Dome Tour. The LCD will display: 1. Tour num:______ 2. Insert Preset 3. Run Tour The controller will support up to 6 tours. Input tour number 1 – 6 and press ENTER to confirm.
Upon completing all settings return to the main menu and press the 5 key Exit Menu. 6. TROUBLESHOOTING
T IPS
a. The ST-PTZMINI-KB is not controlling the camera at all – (i) be sure the R485 connections between the ST-PTZMINI-KB and the camera are using the same polarities;...
APPENDIX 1: KEYBOARD SHORTCUTS Working Operation Mode Shortcut Function Object IR remote ON/OFF Press【SET】for 2 Keyboard seconds Enter the system setting Press 【MENU】for 2 Keyboard seconds Input Dome ID, press 【CAM 【N】+【CAM】 High speed dome 】to select object dome. Zoom in 【Rotate the joystick High speed dome anti-clockwise】...
Page 17
record pattern path. Press【SET】 and input0, 【SET】+【0】+【 High speed dome Press【PATTERN】to save PATTERN】 path Input the pattern path(1-4) 【N】+【PATTERN High speed dome ,Press 【 PATTERN】 to start 】 pattern Input the TOUR NO, press 【N】+ 【TOUR】/ 【TOUR】 or directly press High speed dome 【TOUR】...