Advertisement
Advertisement
Summary of Contents for DIGISYNTHETIC DS212
- Page 1 Instruction Manual...
- Page 2 The dealer will not except failing of such. The consignee must make all shipping claims. The DS212 fits into a standard 19" rack unit of space (1 3/4"). Allow at least an additional 4" depth for the connectors on the back panel. Be sure that there is enough air space around the unit for cooling and ventilation.
- Page 3 DIGISYNTHETIC PRO MODE DS212 FILTER SEL CH L BYPASS FEEDBACK EXTERMINATOR CLIP FILTER MODE CH R STORE CLIP POWER COUPLE MIDI PARAM/PUSH 64/128 time over-sampling for ultra-high resolution, 24-bit A/D & D/A converter, precise analysis 12 auto detect feedback frequencies in every channel, intelligent management...
-
Page 4: Table Of Contents
TABLE OF CONTENTS 1. Introduction 2. Control Panel 2.1 Menu Function Illustration 2.2 Function Buttons & Jog Wheel 2.3 Combination Key & Button 2.4 Rear Panel 3. Function & Feature instruction 3.1 Enable & Disable Filter mode 3.2 Filter/Parametric EQ Menu 3.3 Auto mode Filter 3.4 Sequence Select 3.4.1 Sequence Adjust... -
Page 5: Introduction
COUPLE MIDI PARAM/PUSH Fig 2.1 DS212 Front Panel There are 6 function buttons for control & editing purpose and 1 LCD display screen in the DS212 Front panel. 2.1 Menu display & functions CLIP EQ-ON FILE CLIP Fig 2.2 Menu selection (1) 2 LED light for left/right input/output indication. -
Page 6: Function Buttons & Jog Wheel
(3) "CH:" -- Adjustable Left/Right channel menu display. "CH: L" & "CH: R" indicate able to edit left & right channel respectively. "CH: LR" means left & right channel is able to edit at the same time. (4) "EQ" -- When this symbol is seen to indicate "EQ-ON". To on all filter: "EQ-OF", Auto & Single not affected, "BYPA."... -
Page 7: Rear Panel
3.2 Manual Filter/Parametric EQ DS212 is able to process any musical signal. To increase or decrease fix frequency level, you may use manual filter to select all these frequencies (parametric EQ mode). Every filter is able to set central frequency, octave band (1/60) &... -
Page 8: Sequence Select
You are not able to release this filtration by going back to SINGLE mode. Once discover new feedback point, DS212 will immediately shirt the previous filter frequency to a new one. If you escape from AUTO & SINGLE mode and entering parameter mode, filter will remain all parameters that have been set. -
Page 9: Midi Control
Fig.3.2 Controller Settings When you select controller 4, you may select different menus from frequency, gain, fine tune frequency. DS212 will send auto filter parameter. The fourth page gives you access to the program change setup. The display reads "ProgramX", here, too. - Page 10 Any MIDI data sent to the DS212 (sequencer, MIDI footswitch, etc) are received via the MIDI IN jack. For example, when you wish to use the DS212 as an effects devices for our guitar rack, you can connect the MIDI IN jack to a MIDI footswitch that allows for selecting program presets. If your rack includes an -other MIDI effects devices (e.g.
-
Page 11: Appendix
4.Appendix 4.1 Frequency data chart Display Display Page 10... - Page 12 4.2 Preset table Preset Filter 1 Filter 2 Filter 3 Filter 4 Filter 5 Filter 6 Filter 7 Filter 8 Filter 9 Filter 10 Filter 11 Filter 12 MONO:9 single shot filters attenuate room resonance before 3 automatic filters destroy variable feedbacks Left Right 2xMONITOR AS FEEDBACK DESTROYER ONLY:7 single shots/5 automatic filters for most monitor setup...
- Page 13 4.3 Specifications Analog Inputs Connectors XLR and 1/4" jack Type RF filtered, servo balanced , 20kOhms unbalanced Impedance 40kOhms balanced, 20kOhms unbalanced Nominal Operating Level -20dB to +4dB Max. Input Level +16dB at +4dB nominal level, +2dB at -20dB nominal level Analog Outputs Connectors XLR and 1/4"...