Sapcon COAT-ENDURE Instruction Manual
  1. Manuals
  2. Brands
  3. Sapcon Manuals
  4. Switch
  5. COAT-ENDURE
  6. Instruction manual

Sapcon COAT-ENDURE Instruction Manual

Admittance level limit switch
Hide thumbs Also See for COAT-ENDURE:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
COAT-ENDURE
Admittance Level Limit Switch
Version 3.0

Advertisement

Table of Contents
loading

Related Manuals for Sapcon COAT-ENDURE

Summary of Contents for Sapcon COAT-ENDURE

  • Page 1 INSTRUCTION MANUAL COAT-ENDURE Admittance Level Limit Switch Version 3.0...

  • Page 2: Table Of Contents

    20 Product Selection Order Code ..........Sapcon Instruments Pvt.Ltd.
  • Page 3 Coat-Endure with Baffle ........
  • Page 4 Error Indication ........... Sapcon Instruments Pvt.Ltd.

  • Page 5: Revision History

    • Copyright: All content on this document, such as text, graphics, logos and images is the property of Sapcon Instruments Pvt. Ltd. The selection, arrangement and presentation of all materials on this document and the overall design of this document is the exclusive property of Sapcon Instruments Pvt.

  • Page 6: Introduction

    • Passive shielding compensation with adjustable coat- 1 Introduction ing immunity. Coat-Endure is a microcontroller based compact coat im- • Output options: Relay, PNP and Analog. mune admittance level limit switch. It is a compact level switch which is suitable for sticky solids, pastes and slur- •...

  • Page 7: Electrical Specifications

    Up to 10 bar Mounting • Screwed: 1/2",1”,1 1/2", 3/4” BSP / NPT • Flanged: As per user specification Probe Length 65 mm and (85 mm to 1500 mm) Insulation Part PTFE / Full PTFE Table 2: Mechanical Specifications Sapcon Instruments Pvt.Ltd.

  • Page 8: Application Specifications

    Please refer to figure 6 and the precautions mentioned below before connecting the device. Material Inlet Source Precautions for connecting Coat-Endure : • Power Supply Rating Make sure the power supplied to the instrument is within the specified range mentioned in Table 1.

  • Page 9: Calibration

    Follow the procedure given below to calibration the For applications using conductive materials (water, acid sensor: based pastes etc.), Coat-Endure needs to be calibrated with • the application material. This will make the instrument spe- Install Coat-Endure in an empty tank.

  • Page 10: Cover Delay

    High Calibration is complete. Figure 19: Saving Cover Delay 11 Cover Delay 5. To test, dip Coat-Endure into the application material Note: Set the value of Cover Delay between 1-25 secs. until the switching point is reached. When the application material covers the probe, the 6.

  • Page 11: Sensitivity

    Coat-Endure has a LED bar display which helps in visual- izing the desired sensitivity level. The device ships with a 2. Set the UNCOVER switch to CLOSE (Opposite of default sensitivity level of 3.

  • Page 12: Failsafe

    Figure 29: Demonstration of LED Bar Display 15 Display Indications 16 Factory Reset As seen in Fig.28, Coat-Endure has STATUS LEDs and a 6-point LED bar display. Follow the steps given below to reset the time delays and sensitivity value to default values. Factory Rest does not 15.1...

  • Page 13: Output Options

    • To see the output mode, press and hold ENTER key. • If the only the first LED lights up, Coat-Endure is oper- ating in the single point switching mode. 18 Error Indication On error, the status LED starts blinking RED and GREEN alternately at a faster rate.
  • Page 14 Switch all DIP switches to open Red Blink position. Use only legal combina- tion of keys. 3 Times RED Blinking and 1 Circuit Error Contact the Customer Support de- GREEN Blink partment at Sapcon. Table 5: Error Indication Sapcon Instruments Pvt.Ltd.

  • Page 15: Product Selection Order Code

    MN15S6 : Screwed Thread, NPT 1-1/2”, SS 316 F10S4 : 1" ASA Flange, 10mm thickness, SS 304 F10S6 : 1” ASA Flange, 10mm thickness, SS 316 F15S4 : 1-1/2” ASA Flange, 10mm thickness, SS 304 F15S6 : 1-1/2” ASA Flange, 10mm thickness, SS 316 Sapcon Instruments Pvt.Ltd.
  • Page 16 Standoff Material (Only with “25T”) STGI : GI (Galvanized Iron) STS4 : SS 304 STS6 : SS 316 Probe Length 0.65H : 65mm 0.85H1.5H : 85mm to 150mm 1.5H15H : 151mm to 1500mm Example - CE-I-SCUTE-PCPG13-D-U-P-MB10S4-S20S4-SH11S4-10T-0.65H Shows First Priority Entity Sapcon Instruments Pvt.Ltd.

Table of Contents