ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no Table of Contents Introduction ........................3 Overview ........................3 Getting started ......................4 3.1. Identify your model type (101 or 150) ..............4 3.2. ID Lock 101 ......................5 Inclusion and Exclusion (Adding or removing) ............
Page 3
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no 7.10. Use case of Single User Code Deleted ............16 7.11. Use case of New User Code Added ..............16 7.12. Use case of User Code Not Added Due to Duplicate Code ......17 7.13.
The ID Lock Z-Wave Module does not support the Basic Set Command Class. Overview Z-Wave Module is a Z-Wave interface device of ID Lock and is used to connect a to Z- Wave Controller using the Z-Wave protocol. This document decribes the spesifics for Z-Wave command classes used when ID Lock Z-Wave Module is interfacing with a Z-Wave controller.
The keypads on 101 and 150 are different. Whilst the 101 has a * (star) and # (hash) left and right of digit “0” the 150 has open and closed padlocks (see pictures below). Note: FW v1.6 of ID Lock Z-Wave Module has reduced compatibility for ID Lock 101. The Z-Wave Module fits only one way below the batteries on both 101 and 150.
ID Lock 101 3.2.1. Inclusion and Exclusion (Adding or removing) For inclusion (puts your device in inclusion mode) of ID Lock 101 first set your designated Z-Wave controller in inclusion mode then press and hold the Key Button [A] until keypad is activated whilst the door lock is open and unlocked.
ID Lock 150 3.3.1. Inclusion and Exclusion (Adding or removing) For inclusion (puts your device in inclusion mode) of ID Lock 150 first set your designated Z-Wave controller in inclusion mode then press and hold the Key Button [A] until keypad is activated whilst the door lock is open and unlocked.
Z-Wave firmware version This chapter contains the release for the Z-Wave Module firmware. ID Lock 150 firmware can and must be updated with the app ID Lock 150 Updater which is available for iOS and Android devices (idlock.no/updater). 4.1.
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no Z-Wave Specifications ○ Device Type: Secure Keypad Door Lock ○ Role Type: LSS (Listening Sleeping Slave) 5.1. Supported Command Classes ◼ Non Secure Mode CLASS Value (Hex)
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no Configuration Parameters These configuration parameter numbers and values are specific for the different applications. COMMAND_CLASS_CONFIGURATION Parameter Parameter Name Size Description Number Values Configuration Door Lock Mode Set parameter...
Page 11
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no Name Parameter Size Value Description Remarks Manual lock Away off Auto lock Default value Away off Lock Mode Manual lock After unlock value 0 Away on Auto lock...
Page 12
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no Name Parameter Size Value Description Remarks Deactivated Default value 1x use Returns to value 0 2x uses Returns to value 0 5x uses Returns to value 0...
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no Notification Parameter These Notification parameters are specific for the applications. ID Lock supports Notification Class (V4) to report events of ID Lock. The type and event is described in table below. COMMAND_CLASS_NOTIFICATION (V4) Event...
Page 14
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no Single user code deleted (0x0D) Single user code added (0x0E) New user code not added due to duplicate code (0x0F) Unknown Unknown PIN Unlock By RF with invalid...
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no 7.1. Use Case of Manual Lock Notification ⚫ Example: Lock the door by thumb turn switch or open/close button Notification Notification Para Type Event Length 0x06 0x01 7.2.
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no 7.4. Use Case of RF Unlock Operation ⚫ Example : Unlock the door by remote unlock (Z-Wave) or RFID Card The value of para1 refers to user identifier for RFID or remote unlock (0x00)
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no 7.8. Use case of Lock Jammed ⚫ Example: unsucsessfull lock or unlock Notification Notification Para Type Event Length 0x06 0x0B 7.9. Use case of All User Code Deleted ⚫...
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no 7.12. Use case of User Code Not Added Due to Duplicate Code ⚫ Example: pin not added due to duplicate pin code Notification Notification Para Type Event...
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no 7.14. Use case of lock by RF with invalid user code Reserved, not implemented on door lock firmware version 1.4.7 (for future use) ⚫ Example: Invalid PIN code Notification Report...
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no Manufacturer Parameter The ID Lock support the Manufacturer Specific Command Class with the following parameters. COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 Name Value Description Manufacture ID 0x0373 ID Lock AS Product Type ID...
0x47 10. User Codes (PINs and RFIDs) 10.1. User code ID status In order to set or reset user codes of ID Lock 150, it is used COMMAND_CLASS_USER_CODE_V1. The User ID Status is defined as below for ID Lock 150...
10.2. Credentials ID Lock 150 Z-Wave module is compatible with COMMAND_CLASS_USER_CODE_V1. In oder to set or reset credentials of ID Lock 150 use commands with identifier number, status and value. Delete all credentials resets Master PIN to [1234]. Credentials table for ID Lock 150:...
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no 11. Door Lock Operation Report Value The Door Lock Operation Report contents is as follows. COMMAND_CLASS_DOOR_LOCK_V2 Parameter Value Description Door Lock Mode 0x00 Door Unsecured 0xFF Door Secured...
ID Lock Z-Wave Module Technical manual for FW 1.6 June 20 2019 idlock.no 13. Association & Association Group Parameter The ID Lock support 1 association group with 5 devices. Notification Reports are sent out unsolicated to device included in the association group.