Specifications Approx. Length Width Height Weight lbs. 11½ 12¾ 1 5 ¼ 4 0 ½ Projector (with cover) Speaker unit 1 3 ½ 12¾ 6 ¼ (Case cover) Arc projector power 16¼ 26 ½ supply unit 5¼ Power Service Required: 105- to 125-volt, 60-cycle ac., 3-wire grounded outlet Maximum Power Consumed: 700 watts...
After a preliminary reading of the instruc tions, practice threading, projecting, and rewinding with a reel of sound film so that you become familiar with the machine before the fi r st show. Kodak How to Use the Pageant Projector...
Page 4
TAKE·UP REEL ---- SUPPLY REEL ARM LAMP SWITCH TONE BALANCE CONTROL AMPLIFIER POWER BUTION SPEAKER JACK VOLUME CONTROL FIGURE 1...
Setting Up Place the (Figure supply unit to start the lamp. This can Push the master control to the OFF POWER SUPPLY UNIT If immediate projection is be noted as a series of clicking noises. position. 1) on a fi r m table or other support of planned, leave the fan and lamp convenient height, with the receptacle After the arc is established, less than...
Preparation for Threading for Threading Sound Pictures Place the reel of film on the SUPPLY Open the supply and take-up sprock Draw off about five feet of leader. SPINDLE (Figure 3) with the fi l m feed et CLAMPS. Grasp the leader near the supply reel Open the GA TE by pushing forward ing clockwise off the reel and the per...
Rewinding After the Show To rewind the fi l m, attach its end Following the projection and rewind directly to the supply reel as shown ing of all reels of fi l m that are to be · (Figure 6) and give the reel a few shown: turns counterclockwise.
Kodak Super-40 Shutter The KODAK PAGEANT Arc Projector is position opposite the fi x ed blade. Now To Lock the SuPER-40 Shutter equipped with the SUPER-40 Shutter the shutter will operate in the 2-blade the 3-Blade Position: (Figure 10), which provides 40 per...
Operating Tips The perforations in the fi l m should be toward you as film comes off the bottom of the supply reel. If they are not, the film has not been rewound or was twisted while being rewound. If the gate is left open, the projected picture will be out of focus. If the picture is unsteady, check the upper and lower loops;...
With the wide variety of lenses Shown in the table are the maxi screens. available for your PAGEANT Arc mum image widths for adequate il The seats nearest the screen Projector, you can tailor your screen...
With a soft, polished surfaces of the gate; then To insert the new lamp, reverse the lintless cloth or Lens Cleaning KODAK withdraw the gate. procedure given above, being careful Paper, carefully· wipe the front and Use a soft, damp, lintless cloth to to fit the lower lip of the lamp reflec...
Oiling Cleaning Sound Cleaning Sound Drum Optics All bearings are self-lubricating and require no oiling. Occasional cleaning of the sound op The sound drum, sprocket-clamp roll tics is recommended. ers, and other rollers that come in Be sure that the power cord is not contact with the film should be wiped plugged in.
Replacing Exciter Replacing Belts Lamp Rewind Belt-Disconnect the two ends the two upper Take-Up Belt-Remove of the worn belt, connect one of these sprocket-plate retaining SCREWS (Figure 20) in EXCITER LAMP ends to an end of the new belt and pull that is located behind the SPACER this projector operates at less than its...
Honolulu, Hawaii 96807 Guarantee Within a year after purchase, any repairs needed for this KODAK PAGEANT Arc Projector due to a defect in materials or workmanship will be made or, at our option, the projector will be replaced without charge. No other war...
Page 20
KODAK PAGEANT Arc Projector KoDAK Microphone, Model PA-8, is currently recommended for use with the KoDAK PAGEANT Arc Projector. This microphone is equipped with a 0.250-inch diameter standard phone plug on the end of an 8-foot cord. Starting with the projector bearing Serial No. 02001, the screw-type connector labeled MICROPHONE RECEPTACLE in Figure 8 of the instruction manual has been replaced by a plug jack that will receive the phone plug.