Advertisement
Available languages
Available languages
E020401CW
When the door is closed, the writing "PRESS
START" appears, press START in order to begin
again the program.
If you press the button STOP one time the
machine puts in stand by: in the display "PAUSE".
Pressing START the program restarts from
interruption: pressing STOP for a second time, the
program will be interrupted.
9. SINGLE CYCLE
A single program may be implemented for single
operation with automatic erase at the end of the
program itself.
Pressing the button SINGLE CYCLE: you are in
the programming of the single cycle. "DURATION
CYCLE" is what appeared on the display: Press
ENTER. On display appears "0": put into the
wished time (1 and 99 minutes) and confirm with
ENTER.
On display appears "TEMPERATURE CYCLE".
Pressing ENTER: On display appears "0". ": put
into the wished time (29 and 90°C) and confirm
with ENTER.
On
display
appears
Pressing START, the cycle just programmed will
start.
10. MEMORISED PROGRAMS
herewith
the
characteristics
implemented programs. The cooling time is equal
to 10 minutes and the cooling temperature is
equal to 30°C for all the programs.
Nr.
Name
0
50 min 90°C
1
40 min 75°C
2
30 min 60°C
3
30 min 45°C
4
40 min 60°C
5
25 min 50°C
6
20 min 45°C
7
30 min 40°C
8
20 min 40°C
9
25 min 40°C
Standard
Nr.
Name
0
COTTON
"PRESSING
START".
of
the
builder
Duration
Temperature
[minutes]
[°C]
50
90
40
75
30
60
30
45
40
60
25
50
20
45
30
40
20
40
25
40
Residual
Temperature
humidity
[°C]
[%]
10
90
1
VELVET
2
WOOL
3
SYNTHETIC
4
Pr. 04
5
Pr. 05
6
Pr. 06
7
Pr. 07
8
Pr. 08
9
Pr. 09
Machine with humidity version
Nr.
Name
0
HIGH
1
MED
2
LOW
Coin op version
11. PROGRAMMING
The characteristics of the ten programs in the
memory can be modified proceeding as follow
Press the buttons "UP" and "DOWN" at the same
time while the display shows "SELECT A
PROGRAM".
Appears
"ENTER".
Appears "0". Insert the code" 777" and confirm
pressing "ENTER". Appears "INSTALATION":
With the buttons "UP" and "DOWN" is possible to
defoliate the parameters and to go out from the
programming system, keeping the modification
done, with the button "STOP" many times up to
the display shows "SELECT A PROGRAM"
The parameters modifiable are:
LANGUAGE
Press "ENTER" in order to modify the parameter.
Appears "ENGLISH". Press the buttons "UP" and
"DOWN" to modify the language seeing the
possibilities. Chosen the language press "ENTER"
to confirm.
INFORMATION
Press "ENTER" in order to modify the parameter.
Appears "WORKING HOURS". Press again the
buttons "ENTER": in the display appears the
hours accumulated since the date of installation of
the machine. To go out from the parameter press
"ENTER". and "DOWN" to change the language
seeing the possibilities. Chose the language and
press "ENTER".
DATE (only for ICD model)
Press "ENTER" in order to modify the parameter.
Change the value using the alphabetical keyboard
12
26/11/04
10
75
10
60
10
45
10
60
10
50
10
45
10
40
10
40
10
40
Duration
Temperature
[minutes]
[°C]
Minimum
90
Time
Minimum
75
Time
Minimum
60
Time
"PASSWORD".
Press
Advertisement
