Climax Hybrid-Panel Series User Manual

Security alarm system

Advertisement

Hybrid Security Alarm System
User Manual
Dec 16, 2020

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Hybrid-Panel Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Climax Hybrid-Panel Series

  • Page 1 Hybrid Security Alarm System User Manual Dec 16, 2020...
  • Page 2: Table Of Contents

    Table of Contents INTRODUCTION _________________________________________________________________________ 1 1.1 S _____________________________________________________________ 2 YSTEM PECIFICATIONS PANEL INFORMATION ___________________________________________________________________ 4 2.1. I ______________________________________________________________ 4 DENTIFYING THE PARTS 2.2. P ____________________________________________________________________ 9 OWER UPPLY GETTING STARTED _____________________________________________________________________ 10 3.1. S _____________________________________________________ 10 ELECTING OUNTING OCATION 3.2.
  • Page 3 SYSTEM SETTINGS _____________________________________________________________________ 69 8.1. A ___________________________________________________________ 69 DMINISTRATOR ETTING 8.2. H ________________________________________________________________ 70 UTOMATION 8.3. S _________________________________________________________________________ 75 CENE 8.4. R ______________________________________________________________________ 77 EPORTING 8.5. C __________________________________________________________________ 80 ETTINGS 8.6. SMTP S ___________________________________________________________________ 82 ETTING 8.7. M ___________________________________________________________________ 83 EDIA PLOAD 8.8.
  • Page 4: Introduction

    Ethernet / Wi-Fi / Cellular connection: Wi-Fi connection provides backup to Ethernet to extend system flexibility.  Multiple Communication Paths: The Hybrid Security Gateway has built-in RF, Z-Wave, and/or ZigBee modules. The Hybrid-Panel Series include the following models: Name Reporting Path Modules Hybrid-Panel-1-LA...
  • Page 5: System Specifications

    1.1 System Specifications Functions Number of areas Number of on-board wired 16 on-board zones, expandable to up to 64 zones in total zones Number of total wired and 40 per area, 320 in total wireless zones Zone expansion module 12, 24, 36, and 48 wired zone expansion module available Number of wired keypads 4 (via RS-485 connection) (KP-35-COMBO)
  • Page 6 US: B2 (1900 MHz) / B4 (1700 MHz) / B5 (850 MHz) RF Frequency F1 868 MHz/ F1 433 MHz RF encryption Private Encryption Method RF protocol Climax ZigBee protocol ZigBee Pro HA 1.2, 2.4GHz Z-Wave 500 series module Z-Wave protocol 868.40 MHz (EU) / 908.40 MHz (US) Wi-Fi 802.11 b/g/n, 2.4GHz...
  • Page 7: Panel Information

    2. Panel Information 2.1. Identifying the parts Top Cover (front view) Top View...
  • Page 8 Top Cover (internal view)
  • Page 9 Back Cover (internal view)
  • Page 10 Cover Fixing Screw LED 1 - Area 1 (Green/Red)  Full Arm mode - Red lighting up  Home/1/2/3 mode - Red flashing  Learning mode - Green lighting up  Walk Test mode - Green flashing LED 2 - Area 2 (Green/Red) ...
  • Page 11 PGM Port To be used as a voltage output port or a dry contact relay output depending on J24 jumper settings. Please refer to 3.3 Hardware Installation for detail. SLA Backup Connection Battery Terminal (not hot swappable) Connect to SLA battery pack, up to two battery packs can be connected. Alternative Hole for Wiring Management x 2 Built-in Power Unit (Input: 16 ~ 18VAC 40VA, Output: 12VDC/2A) Please refer to 3.3 Hardware Installation for detail.
  • Page 12: Power Supply

    battery pack depending on capacity purchased to serve as a backup power source. Room for Zone Expansion Module (12, 24, 36, or 48 zone, not hot swappable) (For Hybrid-Panel-3/3B): with built-in module adding up to 48 hardwired zones Connector for Expansion Board 2.2.
  • Page 13: Getting Started

    3. Getting Started Read this section of the manual to learn how to set up your Control Panel. 3.1. Selecting Mounting Location The Control Panel is designed to be wall mounted and protected against unauthorized case opening or removal from its mounting surface, follow guidelines below when planning installation location: ...
  • Page 14: Mounting

    3.2. Mounting Before installation or any maintenance work, make sure the power supply has been disconnected, and the battery switch has been slid to OFF position. Step 1. Use a flat-head screwdriver to loosen the cover fixing screw to open the top cover. Step 2.
  • Page 15 Step 6. Peel the release film of the tape. Apply it to your battery pack and press firmly for 30 seconds to ensure good contact. Please avoid applying the tape on uneven surface or re-apply it. <NOTE>  The images below illustrate where users should apply the Velcro tape(s) for different battery type and capacity.
  • Page 16 Step 7. Complete wiring following the instructions in later section 3.3. Hardware Installation. Step 8. Arrange all wires along the wire clips and then route the wires to the two cable holes on top. Use cable ties (not included ) to thread through the wire clips and secure the wires.
  • Page 17 Step 9. Close the cover and tighten the cover fixing screw.
  • Page 18: Hardware Installation

    3.3. Hardware Installation CAUTION: Before servicing, make sure the AC power has been disconnected, and the battery switch has been slid to OFF position. Step 1. For configuration and operation of the Control Panel via Ethernet, connect an Ethernet cable to RJ-45 port. Step 2.
  • Page 19 Zone Wiring (Zone 1 -16)  The 16 zones can be wired to supervise NC (normally close) or NO (normally open) devices. Connect hardwired devices into any Zone terminal.  Wire gauge: Minimum 20 AWG, maximum 18 AWG. Do not use shielded wire. ...
  • Page 20 Double-End-of-Line Resistor Wiring AUX Power Wiring  The Control Panel can provide a maximum of 12V 400mA current for hardwired zones, auxiliary output and KP-35-COMBO.  Min/Max operating voltages for devices/detectors is 11.4VDC -13VDC.  Please note that the total current should not exceed 400mA, otherwise, an additional power supply is required.
  • Page 21 PGM Wiring  The PGM port can be a voltage output port or a dry contact relay output depending on J24 jumper settings.  When J24 Jumper Switch is disconnected, PGM port will operate as a dry contact relay output. ...
  • Page 22 Wired Zone Expansion  Hybrid Security Alarm System is compatible with HWC-1 Wireless Converter. One HWC-1 can add 9 wired zones to the Control Panel. Bell Wiring  The total current drawn from the PGM and Bell port must not exceed 400mA. Min/Max operating voltages for devices / detectors is 11.4VDC -13VDC.
  • Page 23 Example  KP-35-COMBO-A is wired correctly as it is within 500’ / 152m of the panel, in wire distance.  KP-35-COMBO-B is wired correctly as it is within 500’ / 152m of the panel, in wire distance. Since it has the furthest distance from the Control Panel, ensure its jumper switch is set to ON to serve as a terminating resistor before tightening the cover fixing screw.
  • Page 24 Ground Wiring  Using an insulated green wire (minimum 22 AWG), connect the EGND terminal and the grounding wire from the building electrical installation. Earth ground connection Ground wire from building electrical installation Battery Installation  The Control Panel can support up to two SLA rechargeable battery packs or one NiMH rechargeable battery pack to serve as a backup power source.
  • Page 25 Using the built-in Power Unit  AC Module built-in Power Unit or Open Frame built-in Power Unit is installed. For AC module, connect 2 wires of the AC Transformer to 2 terminals of the built-in Power Unit. For Open Frame, connect BROWN wire of the power cord to Terminal L of the built-in Power Unit, and connect BLUE wire to Terminal N.
  • Page 26  Open Frame built-in Power Unit:...
  • Page 27 Caution:  Wiring of the Hybrid Alarm System should only be performed by certified technician with proper knowledge and training in electric equipment.  Before installation or any maintenance work, make sure the power supply has been disconnected.  Do not connect the devices to loads exceeding supported load current. ...
  • Page 28: Software Installation

    The Finder software is required for your computer to identify the control panel on the LAN. Step 1. To download Finder software, open your browser and type below URL in the address bar: http://www.climax.com.tw/climax-download-finder.html. Step 2. After download, install the software and follow on-screen instructions to complete installation.
  • Page 29 Step 6. If the panel information is not displayed, check panel power and Ethernet connection and click on ―Search‖ to update the panel information. (Optional)You can choose to edit the panel’s network setting by clicking on the panel Step 7. column, then click ―Configure Setting‖...
  • Page 30 The LanType is default to DHCP and does not require manual input of IP/Netmask/Gateawy/DNS setting. If you wish to configure these setting manually, change LanType to Static. After finish changing network setting, enter the user name (default: admin) and password (default: cX+HsA*7F1) then click OK to confirm. The user name and password can be changed later in panel configuration webpage Click the panel information column and click on ―Open Web Page‖, or double click on Step 8.
  • Page 31: Connection To Panel Webpage

    4. Connection to Panel Webpage For first time setup, webpage connection is only available within 1 hour after the panel is powered on; if the panel has been powered on for more than 1 hour. Webpage access will be disabled. Reboot the panel to enable webpage function again. Select the Control Panel in the Finder software and click on ―Open Webpage‖...
  • Page 32: Device Management

    320 zones of accessory devices, in 8 areas, up to 40 zones each area. The following types of accessory devices are supported:  RF device: All Climax RF devices are supported. (For ZigBee only model, RF devices are not supported.) ...
  • Page 33 Step 4. When the system received the signal transmitted from device, the screen will display its information for selection. <NOTE>  It takes 5-10 seconds for the Control Panel to receive a learn code from ZigBee or Shutter Control Sensor. Step 5.
  • Page 34 Control Panel emits one short beep. LED 1 & 2 (Green) will turn ON to indicate the Control Panel is now in learning mode. Step 2. Press the test or learn button on each device to transmit signal, refer to device manual for detail.
  • Page 35 Step 2. You will enter Device Edit webpage Step 3. Edit your device setting and information according to instruction below. Click ―OK‖ to save your new changes when finished. Alternatively, click ―Default‖ to reset all parameters to default values or click ―Reset‖ to re-enter all the information. ...
  • Page 36  Latch report This function ONLY applies to Remote Control or Door Contact with Set/Unset attribute enabled.  Latch Report ON: When the device is used to change systm arm mode, the Control Panel will report the arm/disarm action by the particular device. ...
  • Page 37  Burglar Follow  When the system is in Full Arm or Home Arm mode mode, if a sensor set to Burglar Follow is triggered, the Control Panel will report a burglar alarm immediately.  When a Start Entry sensor is triggered and the system is under Entry Delay Timer countdown, if a sensor set to Burglar Follow is triggered, the Control Panel will wait until the Entry Delay Timer expires before activating a burglar alarm.
  • Page 38  24HR  A sensor set to 24HR attribute will ignore Disarm, Full Arm, Home are and Exit response setting. The panel will activate selected alarm when this sensor is triggered regardless of system mode under any time. <NOTE>  Some devices have their own unique functions and will have its own attribute setting which is not listed in this section.
  • Page 39: Add Rf Device

    5.2. Add RF Device Besides learning, you can also add RF devices into the system by entering its RF code into the system with Add RF Device function. Step 1. Click Add RF Device. Step 2. Select Area and Zone number for the device you wish to add into system. Step 3.
  • Page 40: Learn Rule

    5.3. Learn Rule You can enter the sensor RF code or ZigBee MAC address manually to assign area and zone number to this sensor. Sensors learned with pre-assigned rule will be put under the area and zone number you specified. This function does not work with Shutter Control devices and DECT device.
  • Page 41 Step 11. Learn in the sensors you have entered rules for according to 5.1.1 Add Sensor. <NOTE>  Learn rule function is only used to pre-assign area and zone number to sensors before learning. To add senor to control panel, you still need to follow the instruction in 5.1.1 Add Sensor to complete the learning process.
  • Page 42: Walk Test

    5.4. Walk Test This is to test the sensor operation range for installation purpose. Step 1. Click ―Start‖ to enter Walk Test mode. Step 2. Press the test button on the sensor(s) or any button on the Remote Controller or triggering the sensor.
  • Page 43: Exclusion

    5.5. Exclusion This feature is only available for Shutter Control modules only, or when a Shutter Control dongle is inserted into the Control Panel. This feature is for you to remove Shutter Control device only. Step 1. Click on ―Exclusion‖ and click on ―Start‖ to start the procedure. Then the Panel will enter the removing mode.
  • Page 44: Shutter Control Tool

    5.6. Shutter Control Tool The Shutter Control Tool is used to reset Shutter Control module to factory default and remove all Shutter Control devices, or change routing setting. Step 1. Click ‖Shutter Control Factory Reset‖, the Shutter Control module is reset to factory default and all Shutter Control devices will be removed automatically.
  • Page 45: Pss Control

    5.7. PSS Control This feature is designed to control/edit/delete Power Switches included in the panel.  Click Edit to edit attributes of power switches.  Click Delete to remove power switch from panel.  Click Switch On/Switch Off to turn on/off power switches. Or click Switch Toggle to toggle between on/off status.
  • Page 46: Upic Control

    5.8. UPIC Control UPIC Control webpage allows you to control UPIC IR Transmitter included in Control Panel.  Transmit IR Signal Depending on the UPIC model number, select the function to be performed in the drop down menu, then click ―Setup UPIC‖ for the UPIC to transmit IR Signal. ...
  • Page 47: Surveillance

    5.9. Surveillance The PIR Camera/Video Cameras and IP Cameras are listed under Surveillance for separate control.  Click Edit to edit camera attributes.  Click Delete to remove device from panel.  Click Request Media to capture a picture or video ...
  • Page 48: Group Control

    5.10. Group Control This feature is designed for you to edit a name of group, switch on or off a group of Power Switches. You can also assign Power Switches to groups you desire. 5.10.1. Group Control/Edit Step 1. Specify a new name for a group. Step 2.
  • Page 49: Sound/Siren Setting

    5.11. Sound/Siren Setting The Sound/Siren Setting page includes setting Siren configuration function. 5.11.1. Device Edit/Delete Click Edit to edit the Siren’s attribute, volume and voice settings, or Delete to delete the Siren. After clicking Edit, you will be directed to the Device Edit page:...
  • Page 50 <NOTE>  The Device Edit page is only available for the newest BX/Siren series and BX series without DIP Switch. Edit your Siren setting and information accordingly to instruction below. Click ―OK‖ to save your new changes when finished. Alternatively, click ―Default‖ to reset all parameters to default values or click ―Reset‖...
  • Page 51  Home arm confirm beep: set the volume of the confirm beep sound of the Siren when Control Panel is put into Home Arm Mode.  Disarm confirm beep: set the volume of the confirm beep sound of the Siren when Control Panel is put into Disarm Mode.
  • Page 52 5.11.2. RF Siren Setup  Tamper On/Off You can enable/disable all RF Sirens tamper protection with this function. Select to turn on or off the sirens tamper function. <NOTE>  When turned off, if siren tamper will be enabled again automatically after one hour if not turn on manually during the one hour period.
  • Page 53: Wired Zones Programming

    5.12. Wired Zones Programming Step 1. Click on ―Wired Sensors‖ to enter this page. Step 2. Edit the type of the wired sensor, zone wiring, and the EOL resistance for each zone.  Type: Select the type of the wired sensor for each zone from the drop down menu. ...
  • Page 54  Resistor: Select the resistance for the zone wiring.  Status: The status of each zone—Restore, Tamper, or Trigger—will be shown in this field. Step 3. Click ―OK‖ to save changes when finished. Alternatively, click ―Reset‖ to re-enter all the information.
  • Page 55 Step 6. Edit your device setting and information according to instruction below. Click ―OK‖ to save changes when finished. Alternatively, click ―Default‖ to reset all parameters to default values or click ―Reset‖ to re-enter all the information.  Name: Enter a name for the device. ...
  • Page 56  Set/Unset This function is for Door Contact only. This function allows Door Contact to control system mode.  Normal Close: The system will be armed when the Door Contact is opened, and disarmed when Door Contact is closed.  Normal Open: The system will be armed when the Door Contact is closed, and disarmed when Door Contact is open.
  • Page 57  Burglar Instant  When the system is under Full arm or Home Arm/ Disarm / Entry Time mode, if a sensor set to Burglar Instant is triggered, the Control Panel will report a burglar alarm immediately.  Burglar Outdoor ...
  • Page 58: System Settings

    6. System Settings After the initial set-up, you can then program your system by clicking on the left menu to set them individually. 6.1. Panel Condition In the Panel Section, user can arm, disarm or partially arm the system. Besides, it displays the current Panel Status &...
  • Page 59  AC activation: To check whether AC power is connected. If not, it will show ―AC Failure‖.  Background RSSI: RSSI value is for you to check the RF environment around the Control Panel. It ranges from 0 to 9, where 0 refers to the weakest and 9 refers to the strongest background noise.
  • Page 60 values will be kept without any change. Note The function is designed for installer to make a note for each control panel. The note you make here can be delivered to a server over XMPP or polling protocol.
  • Page 61: Panel Settings

    6.2. Panel Settings Program the Panel, Time and Sound Settings at your discretion. Panel Setting  AC Fail Report: When an AC power failure is detected, your Control Panel will report to the Central Monitoring Station according to the duration set under AC Fail Report. If 5 minutes is set, the event will be automatically reported to the CMS after 5 minutes.
  • Page 62 convert to sleep mode to conserve battery power. During this period, both GSM and Ethernet port will be powered off, while the RF and ZigBee modules will keep working. If 5 seconds is set, both GSM and Ethernet port will be powered off after 5 seconds.
  • Page 63  Supervision Check: Select to enable or disable system supervision function. When ON is selected, the Control Panel will monitor the accessory devices according to the supervision signal received. Time Setting  Supervision Timer: The Control Panel monitors accessory devices according to the supervision signal transmitted regularly from the device.
  • Page 64 Sound Setting  Door Chime Setting: this function is available only when the attribute of Door Contact (DC) and/or PIR detector (IR) is set as Door Chime. The Control Panel sounds a Door Chime (Ding-Dong Sound) while the DC and/or IR is activated in Disarm / Full / Home / Entry mode.
  • Page 65: Pin Code

    6.3. PIN Code The User PIN Codes are used by Remote Keypad accessory to control system mode remotely. The 2 areas in the control panel each has 30 User PIN Codes available for setting. Each consists of 4-6 digits (numeric number 0~9), no disallowed PIN code. User PIN code #1 for each Area is always activated factory default.
  • Page 66: Network Settings

    7. Network Settings 7.1. GSM Check SIM This is designed for the system to check the SIM card or not. (If users do not intend to use the GSM funciton, please tick “NO” to ensure the system will not check if the SIM card is inserted or not and it will not display the GSM fault by LED flashing.) GPRS In order to allow GPRS to serve as a back-up IP Reporting method, this section will need to...
  • Page 67 It is the name of an access point for GPRS. Please inquire your service provider for an APN. When APN is set, the system becomes valid for internet connection.  User (GPRS) It is the Log-in name to input before accessing the GPRS feature. Please inquire your service provider.
  • Page 68 Send SMS Message This feature is designed for you to send a SMS message on this web configuration page. Step 1. Click Send SMS. Step 2. Enter a desired phone number and text message. Reset GSM This feature is designed for you to reset GSM module. Step 1.
  • Page 69: Network

    7.2. Network This is for you to program the Network for IP connection.  Obtain an IP address automatically (DHCP) If DHCP is selected, the Network will obtain an IP address automatically with a valid Network DHCP Server. Therefore, manual settings are not required. This is only to be chosen if your Network environment supports DHCP.
  • Page 70: Wireless

    7.3. Wireless Use ―Wireless‖ webpage to setup the panel’s WiFi setting There are 3 ways you can connect to the wireless network. 1. Search for WiFi AP: Click ―Scan WiFi AP‖ to search for available wireless network Select the available Wireless APs from the list by clicking ―Set‖ after AP info column and enter the required information (pre-shared key, etc.) and click the ―OK‖...
  • Page 71: Upnp

    7.4. UPnP UPnP is Universal Plug and Play, which opens networking architecture that leverages TCP/IP and the Web technologies to enable seamless proximity networking in addition to control and data transfer among networked devices in the home, office, and public spaces. ...
  • Page 72: System Settings

    8. System Settings 8.1. Administrator Setting For setting new Administrator Log-in Name and Password. Please note both User Name and Password are case sensitive. Step 1. Enter the preferred User Name. Step 2. Enter the preferred Password in the ―New Password‖ field and repeat the same Password in the Repeat Password field.
  • Page 73: Home Automation

    8.2. Home Automation It is used to set Home Automation rules to control sensors and home appliances. You can set up to 100 rules. Step 1. Click on Edit. Step 2. Select an operation area. Step 3. Set a rule condition. Step 4.
  • Page 74  Mode Change and Exit Timer Stopped : When set as Mode Change and Exit Timer Stopped, when the system changes mode to and Exit Delay Timer expires, , the rule will be activated according to rule schedule and execution setting. ...
  • Page 75  LUX Between : When set as LUX Between, if the lux reading from specified light sensor falls below the level specified, the rule will be activated according to rule schedule and execution setting.  Random : The Random condition must be used along with Rule Schedule setting. Set a percentace from 1 to 10%.
  • Page 76  Zone Swich On For : Turn on the Power Switch at specified zone for a set duration.  Zone Switch Level:: Change the power output level for Dimmer at specified zone.  Zone Swich Toggle : Toggle on/off the Power Switch at specified zone. ...
  • Page 77  Request Image (No Flash): The PIR Camera in specified zone will take a picture.without activating its LED flash.  Request Image (All, No Flash) : All PIR Cameras in the system will take a picture without activating LED Flash. ...
  • Page 78: Scene

    8.3. Scene The Scene setting allows you to customize a series of actions with your devices, such as Power Switch control, image/video request, mode change and trigger alarm. The programmed scene can be set to activated when a device is triggered. (See 5.1.3. Edit Devices), or when a Home Automation Rule is excecuted.
  • Page 79 included in one scene. Step 6. Click ―Done‖. Step 7. Click ―OK‖ at bottom of webpage to confirm the new scene setting..
  • Page 80: Reporting

    This is used for installer to program/ set all requirements for reporting purposes.  Reporting URL This is used for installer to program report destinations. Climax CID protocol via IP Format: ip://(Account Number)@(server ip):(port)/CID Example: ip://1234@54.183.182.247:8080/CID SIA DC-09 protocol via IP...
  • Page 81 ip://1234@54.183.182.247:8080/CID_SIA/KEY/4A46321737F890F654D632103F86B4 CSV protocol via IP Format: ip//(Account Number)@(server ip):(port)/CSV Example: ip://1234@54.183.182.247:8080/CSV CSV protocol via IP including username and password Format: ip//(Account Number)@(server ip):(port)/CSV/User/Pasword Example: ip://1234@54.183.182.247:8080/CSV/abcd/1357 Email Format: mailto:user@example.com Example: mailto:john@gmail.com  Level Select a reporting condition: All events: The system will report all events to this destination. Alarm events: The system will only report alarm event to this destination.
  • Page 82 <NOTE>  When the panel is registered into Climax’s Home Portal Server, URL1 will be filled in with Home Portal Server report information. Do not change the information once registration is complete or reporting to Home Portal Server may encounter error.
  • Page 83: Code Settings

    8.5. Code Settings The Duress Code, Master Code & Temporary Code adds the flexibility of different security level for operation in Code Settings menu. Step 1. Key in your preferred 4-6 digit Installer Code, Duress Code, Master Code, and/or Temporary Code. Step 2.
  • Page 84 to program the code setting in this area.  Duress Code The Duress Code is designed for transmitting a secret & silence alarm. When Duress Code is used for accessing the system, the Control Panel will report a secret alarm message without sounding the siren to the Central Monitoring Station to indicate of a Duress Situation in Progress.
  • Page 85: Smtp Setting

    8.6. SMTP Setting Program the mail server related settings. The email account you set here would be used to send report for events or picture and video clip captured by PIR Camera and PIR Video Camera. Step 1. Enter the following settings: ...
  • Page 86: Media Upload

    8.7. Media Upload The system can deliver captured images and video clips captured by PIR Cameras and PIR Video Camera to cell phone, email or FTP.  FTP: ftp://user.password@server/path  HTTP: http://ip:port/path  Email: mailto:user@server (transmitting an alarm image over Ethernet) ...
  • Page 87: Polling

    8.8. Polling The polling function enables the Control Panel to query the destiation you set (URL1 or URL2) in turn as to whether it has any data to transmit.  URL/URL2: ip://server:port/path  Interval : interval time of polling...
  • Page 88: Xmpp

    XMPP setting enables the Control Panel to query the set destination. This setting is required for the Control Panel to connect to Climax’s Home Portal Server for remote control. If the panel is disconnected from the server, it will retry connection every 3 minutes.
  • Page 89: Date & Time

    8.10. Date & Time Program the current Date & Time and set automatic synchronization with internet time server.  Date & Time: set current month, date and time.  Time Zone: choose your time zone, and then the system will calculate the daylight saving time automatically (if necessary).
  • Page 90: Dynamic Dns

    8.11. Dynamic DNS This page is used to provide you the Control Panel’s current public IP address.  Dynamic DNS Server: http://checkip.dyndns.org...
  • Page 91: Test Ip

    8.12. Test IP This is for you to test the Control Panel internet connection. Step 1. Enter the URL destination you want to test connection to. Step 2. Enter the test interval. Click ―OK‖ Step 3. You can check the test connect result in System Log.
  • Page 92: Firmware Upgrade

    8.13 Firmware Upgrade You can update the firmware via this web page. Click on ―Choose File‖ and locate the latest firmware file in your PC. Step 1. Press ―Apply‖ to upload the latest firmware to Control Panel Step 2. Step 3. Wait for 1 min and do NOT power off during this time.
  • Page 93: Rf Firmware Upgrade

    8.14. RF Firmware Upgrade You can update the Control Panel’s RF firmware via this web page. Click on ―Choose File‖ and locate the latest firmware file (―unzipped image.bin‖ file) Step 1. in your PC. Press ―Apply‖ to upload the latest firmware to Control Panel Step 2.
  • Page 94: Io Mcu Firmware Upgrade

    8.15. IO MCU Firmware Upgrade Step 1. Click ―Firmware/IOMCU‖ to enter this page. Step 2. Click on ―Choose File‖ and locate the latest firmware file in your PC. Press ―Apply‖ to upload the latest firmware to Control Panel Step 3. Step 4.
  • Page 95: Factory Reset

    8.16. Factory Reset Yan can clear all programmed parameters in the Control Panel and reset it to Factory Default. Once the Factory Reset is executed, all the programmed settings will returned to its default value, and all the learnt-in devices will be removed. You will need to restart the programming and learning process again.
  • Page 96: Backup & Restore

    8.17. Backup & Restore Yan can back up all programmed parameters and save these programmed values into a file. Besides, you also can restore pre-programmed settings. 8.17.1 Backup Data Click Download, and you can back up all programmed data and save these programmed values into a file.
  • Page 97: System Log

    8.18. System Log The sytem log webpage logs the control panel’s detail system operation history.  System Log File Download: Click to download a detail log files into your computer for more information.
  • Page 98: Event & History

    9. Event & History This section introduces event history of the system. 9.1. Captured Events This page stores all captured pictures and videos by PIR Camera and PIR Video Camera. When a PIR Camera is triggered, it will take 3 pictures in quick succession, when a PIR Video Camera is triggered, it will take a 10-second video clip.
  • Page 99: Reported Events

    9.2. Reported Events This page stores all triggered events by the control panel by recording the events’ CID event code and report status.  Reload : Click to refresh the page content  Limit # of Items: Click the drop down menu on the pageto select the numbers of captured events you want to display.
  • Page 100: Event Log

    9.3. Event Log The Event Log page records specific actions performed by the Control Panel and accessory devices.  Reload : Click to refresh the page content  Limit # of Items: Click the drop down menu on the pageto select the numbers of captured events you want to display.
  • Page 101: Device History

    9.4. Device History You can track your ZigBee accessory device status history under Device History. For Power Switch Meter or Temperature Sensor, the update history power consumption or temperature ireading will be displayed under this page (the current info is also displayed under Panel and PSS Control).
  • Page 102: Appendix

    Appendix 10.1. Fault Event Description During operation, when the panel detects faulty events, the panel will log the event and make reports. When fault events exist in the system, the panel Fault LED will light up and the panel will emit a beep every 30 seconds.
  • Page 103: Control Panel Mode And Response Table

    10.2. Control Panel Mode and Response Table For Alarm Activation by Events and Control Panel Responses, please refer to the following table: System Mode / Status Attribute Under Exit Under Exit Under Entry Disarm Full Arm Home Arm Timer (No Timer Timer Response)
  • Page 104 Alarm Alarm Alarm Alarm Alarm Instant Instant Instant Instant Instant Instant 24H – Medical Medical Medical Medical Medical Medical Medical Alarm Alarm Alarm Alarm Alarm Alarm Instant Fire Instant Fire Instant Fire Instant Fire Instant Fire Instant Fire 24H – Fire Alarm Alarm Alarm...
  • Page 105: Cross Zone Verification

    10.3. Cross Zone Verification Cross Zone Verification is use to setup cross verification for intrusion sensors. To use Cross Zone Verification, the following sensor and panel setting must be adjusted: At least 1 intrusion sensor must be set to Cross Zone attribute. The Cross Zone Timer option under Panel Setting webpage must be enabled.
  • Page 106: Fire Verification

    10.4. Fire Verification Fire Verification is use to setup verification for Smoke Detector. To use Fire Verification, the following sensor and panel setting must be adjusted: At least 1 Smoke Detector must be set to 24 HR – Fire with Verification attribute. The Fire Verification Timer option under Panel Setting webpage must be enabled.
  • Page 107: Contact-Id Protocol & Format

    10.5. Contact-ID Protocol & Format Where ACCT MT QXYZ GG C = 4 Digit Account number (0-9, B-F) ACCT = Message Type, 18H. = Event qualifier, which gives specific event information: = Event code (3 Hex digits 0-9, B-F) = Group, Partition number (00H), or Area Number - 00 = panel - 01= area 1…..xx= area xx...
  • Page 108: Event Code

    10.6. Event Code  100 – Medical  When a device set to Medical attribute is triggered.  101 – Personal emergency  When a device set to Personal Emergency attribute is triggered.  110 – Fire  When a device set to Fire attribute is triggered. ...
  • Page 109  When the panel receives signal again from sensor that previously failed supervision.  154 – Water leakage  When the Water Sensor connected to Door Contact set at Water (@W) is triggered.  158 – High Temperature Alarm  When high temperature alarm is triggered.
  • Page 110  407 – Disarm/Away Arm/Home Arm by Remote Keypad  408 – Set/Unset Arm/Disarm  When the DC set at Set\Unset is triggered.  456 - Partial Arm  When partially arm the system from Disarm to Home arm  570 –...

Table of Contents

Save PDF