Wilbur Curtis Company Gemini GEM-612ILD Instructions Manual

F F
IND OUT MORE IND OUT MORE
. .
ON THE WEB ON THE WEB
WILBURCURTIS.COM WILBURCURTIS.COM
Models Included
GEM-612ILD
GEM-600ILD
TL-9002
TL-9001
WARNING HOT LIQUID,
Scalding may occur.
Avoid splashing.
CAUTION: CAUTION: Please use CAUTION:
CAUTION: CAUTION:
this setup procedure
before attempting to use
this brewer. Failure to follow the
instructions can result in injury or
the voiding of the warranty.
I M P O R I M P O R I M P O R T T T T T A N T I M P O R I M P O R A N T A N T A N T: : : : : A N T
Equipment to be
installed to comply with
applicable federal, state, or local
plumbing/electrical codes having
jurisdiction.
CAUTION: DO NOT CAUTION: CAUTION: CAUTION: CAUTION:
connect this brewer to
hot water. The inlet valve
is not rated for hot water.
WARNING TO AVOID WARNING WARNING WARNING WARNING
SCALDING, Do not
remove brewcone while
brew light is flashing.
C
ISO 9001 REGISTERED
WILBUR CURTIS COMPANY
Montebello, CA 90640
W W W W W
ILBUR ILBUR
ILBUR ILBUR ILBUR
Gemini Digital Brewers – Instructions
This appliance is designed for commercial use. Any servicing other than cleaning and maintenance should be performed by an
authorized Wilbur Curtis service center.
• Do NOT immerse the unit in water or any other liquid
• To reduce the risk of fire or electric shock, do NOT open top panel. No user serviceable parts inside. Repair should be done
only by authorized service personnel.
• Keep hands and other items away from hot parts of unit during operation.
• Never clean with scouring powders, bleach or harsh implements.
Conventions Conventions Conventions Conventions Conventions
W W W W W ARNINGS – ARNINGS – ARNINGS – ARNINGS – T T T T T o help a ARNINGS – o help a o help a o help a o help avoid personal injur
Important Notes/Cautions – from the factory Important Notes/Cautions – from the factory Important Notes/Cautions – from the factory Important Notes/Cautions – from the factory Important Notes/Cautions – from the factory
Sanitation Requirements Sanitation Requirements
Sanitation Requirements Sanitation Requirements Sanitation Requirements
Y Y Y Y Y our Curtis our Curtis our Curtis our Curtis our Curtis ADS System is F ADS System is F ADS System is F ADS System is Factor ADS System is F
Following are the Factory Settings for your interLock Coffee Brewing Systems:
• Brew T T T T T empera • Brew • Brew • Brew • Brew emperature = empera empera empera ture = ture = 200°F ture = ture =
• Brew Volume = • Brew Volume = • Brew Volume = • Brew Volume = Set to 36 cup vessel requirements. • Sleep Mode = • Brew Volume =
System Requirements:
• Water Source • Water Source • Water Source • Water Source • Water Source 20 – 90 PSI (Minimum Flow Rate of 1 GPM)
• Electrical: • Electrical: See attached schematic for standard model or visit www.wilburcurtis.com for your model. • Electrical: • Electrical: • Electrical:
SETUP STEPS SETUP STEPS SETUP STEPS
SETUP STEPS SETUP STEPS
The unit should be level (left to right and front to back), located on a solid counter top. Connect a water line from the water filter
to the brewer. NOTE: Some type of water filtration device must be used to maintain a trouble-free operation. (In areas with
extremely hard water, we suggest that a sedimentary and taste & odor filter be installed.) This will prolong the life of your brewing
system and enhance coffee quality.
The National Sanitation Foundation requires the following water connection:
1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) so that the machine can be moved
for cleaning underneath.
2. In some areas an approved backflow prevention device may be required between the brewer and the water supply.
1. A 3/8" NPT x 1/4" Flare elbow has been supplied for water line connection. Use tubing sized sufficiently to provide a
minimum of 1.0 GPM.
2. To hookup the InterLock grinder, Locate the jack labeled "Class 2 Wiring Only" on brewer and grinder. Connect the two with
the cable plug.
3. Connect the unit to an appropriate electrical power circuit.
4. Turn on the toggle (STANDBY/ON) switch behind the unit. The heating tank will start to fill. When the water level in the
tank rises to the correct volume, the heating elements will energize automatically. With ADS Systems there is no danger
of element burnout caused by an empty tank.
5. The heating tank will require 20 to 30 minutes to reach operating temperature (200°F) as indicated by the READY-TO-
BREW indicator.
6. Prior to brewing, dispense 12 ounces of hot water through the hot water faucet.
7. Brew a cycle of at least 12 ounces, to purge the water lines of any air that may be trapped after filling.
BREWING INSTRUCTIONS BREWING INSTRUCTIONS
BREWING INSTRUCTIONS BREWING INSTRUCTIONS BREWING INSTRUCTIONS
1. Brewer should be ON (Confirm at rear toggle switch, then press the ON/OFF button). Ready-to-Brew should be ON. If
connected to an InterLock grinder, grinder should be on. If Interlocked, grind coffee at this time.
2. Place an empty Satellite on the warmer deck, under the brewcone and press the warmer switch.
3. Place a clean filter 4. Fill brewcone with
into the brewcone.
FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO
C C C C C C C C C C
URTIS URTIS OMP OMP
URTIS URTIS URTIS OMPANY OMP OMP
void personal injury y y y y void personal injur void personal injur void personal injur
actor actor actor actory Pre-Set and Read y Pre-Set and Read y Pre-Set and Read y Pre-Set and Read y Pre-Set and Ready to Go... Right from the Carton. y to Go... Right from the Carton. y to Go... Right from the Carton. y to Go... Right from the Carton. y to Go... Right from the Carton.
• Water Bypass = • Water Bypass = • Water Bypass = On for 36 cup only • Water Bypass = • Water Bypass =
• Sleep Mode = • Sleep Mode = • Sleep Mode = Off • Sleep Mode =
5. Transfer filled
ground coffee. brewcone to
brewer.
WWW.WILBURCURTIS.COM
, I , I , I , I , I . . . . .
ANY ANY NC NC
ANY ANY NC NC NC
6. Press Brew button.
Brewing will begin
immediately.
1