Advertisement
Quick Links
INSTALLATION GUIDE AND OWNER'S MANUAL
MODELS
COVERED:
READ THE GENERAL SAFETY SECTION AND THE ENTIRE MANUAL BEFORE
INSTALLING OR OPERATING THIS WATER HEATER. FAILURE TO FOLLOW
THE SAFETY RULES MAY CAUSE THE UNIT TO OPERATE IMPROPERLY,
WHICH COULD LEAD TO DEATH, SERIOUS BODILY INJURY AND/OR
PROPERTY DAMAGE. READ THE ENCLOSED WARRANTY CARD. WARRANTY
OF THIS WATER HEATER WILL DEPEND ON PROPER INSTALLATION AND
OPERATION. THE WARRANTY SHALL BE VOID IF THE DESIGN HAS BEEN
ALTERED. THE MANUFACTURER OF THIS HEATER WILL NOT BE LIABLE FOR
ANY DAMAGES BECAUSE OF FAILURE TO COMPLY WITH THE INSTALLATION
AND OPERATING INSTRUCTIONS OUTLINED ON THE FOLLOWING PAGES.
DISCONNECT THE POWER CIRCUIT BEFORE SERVICING.
THE INSTALLATION MUST CONFORM TO THE INSTRUCTIONS IN
THIS MANUAL; ELECTRIC COMPANY RULES; AND LOCAL CODES, OR IN
THE ABSENCE OF LOCAL CODES, WITH THE LATEST EDITION OF THE
NATIONAL ELECTRICAL CODE. THESE PUBLICATIONS ARE AVAILABLE FROM
YOUR LOCAL GOVERNMENT, PUBLIC LIBRARY, OR ELECTRIC COMPANY.
IF YOU REQUIRE ANY HELP OR HAVE ANY QUESTIONS RELATING TO THE
INSTALLATION OR PERFORMANCE OF THIS HEATER, PLEASE CALL OUR
TECHNICAL SERVICE DEPARTMENT TOLL FREE : 1-800-543-6163.
HAVE THE INFORMATION LISTED BELOW WHEN CALLING :
S/N __________ MODEL # ___________________ INSTALL DATE ___________
EEMAX
ProAdvantage Series 1
ELECTRIC INSTANTANEOUS WATER HEATER
PA004120T 1Φ 120V
PA008208T 1Φ 208V
PA005240T 1Φ 240V
PA007240T 1Φ 240V
WARNING
1
PA010240T 1Φ 240V
PA012240T 1Φ 240V
PA008277T 1Φ 277V
PA010277T 1Φ 277V
Advertisement
Related Manuals for EemaX ProAdvantage PA004120T
Summary of Contents for EemaX ProAdvantage PA004120T
- Page 1 EEMAX ProAdvantage Series 1 ELECTRIC INSTANTANEOUS WATER HEATER INSTALLATION GUIDE AND OWNER’S MANUAL PA004120T 1Φ 120V PA010240T 1Φ 240V MODELS PA008208T 1Φ 208V PA012240T 1Φ 240V COVERED: PA005240T 1Φ 240V PA008277T 1Φ 277V PA007240T 1Φ 240V PA010277T 1Φ 277V WARNING READ THE GENERAL SAFETY SECTION AND THE ENTIRE MANUAL BEFORE INSTALLING OR OPERATING THIS WATER HEATER.
-
Page 2: General Safety
GENERAL SAFETY The “Eemax ProAdvantage” heater is specifically designed to take in cold or hot water and heat it up to a maximum of 140F (60C). To obtain optimum performance and energy savings, the unit should be located as near as possible to the point of use. The unit is supplied with 1/2”... - Page 3 PA008208T Kitchen 1Φ 240V: PA005240T, PA007240T, PA010240T, PA012240T 1Φ 277V: PA008277T, PA010277T Requirements Eemax Max Output: 3.5 kW @ 120 volts 8.3 KW @ 208 volts 11.5 kW @ 240 volts Hot outlet Cold inlet 10.0 kW @ 277 volts...
- Page 4 Mounting Layout for Series 1 Systems Fig 1...
-
Page 5: Plumbing Hook-Up
II. PLUMBING HOOK-UP 1) The unit is supplied with ½” compression fittings (Figure 2a ). 2) DO NOT USE PIPE DOPE AND DO NOT SOLDER TO THE INLET OR OUTLET. 3) Take care to ensure that the pipes are correctly aligned with the inlet and outlet bosses in order to avoid excessive stress on the heater body molding. - Page 6 MINIMUM - 8” CLEARANCE ABOVE UNIT Contactor Figure 2b Wire nut (GND) Pipe support Union Pipe support Outlet Isolating Threaded type Elbow(s) Ball Valve Teflon tape only (throttle open Inlet Isolating No pipe dope just enough to Ball Valve. (Always obtain adequate leave fully open when flow of hot water)
-
Page 7: Electrical Hook-Up
III. ELECTRICAL HOOK-UP WARNING BEFORE DOING ANY WORK ON THE UNIT BE SURE THE BREAKER IS “OFF” TO AVOID ANY DANGER OF SHOCK. “Eemax ProAdvantage” heaters are manufactured to the following specifications: Table 1 MODEL TYPE Voltage kW output AMPERAGE... - Page 8 IV COMMISSIONING YOUR HEATER IMPORTANT BEFORE SWITCHING “ON” THE POWER AT THE MAIN CIRCUIT BREAKER PANEL MAKE SURE THAT THE HOT WATER CIRCUIT IS FREE OF AIR POCKETS OR ELSE PREMATURE FAILURE OF THE ELEMENT WILL OCCUR. TO DO THIS OPEN ALL HOT WATER OUTLETS ONE AT A TIME FOR A MINUTE OR TWO UNTIL THE WATER FLOW IS CONTINUOUS AND FREE FROM “GULPING”...
-
Page 9: Troubleshooting
Figure 5 The resistance reading should be 4-15 ohms. If the resistance is much greater than this value, call Eemax for a replacement element. SYMPTOM “B”: LOW OR NO HEAT, INDICATOR LIGHT - ON 1) WATER FLOW TOO HIGH Reduce the water flow by adjusting the outlet ball valve. - Page 10 TRIAC HEATER CORE Figure 6 CONTROL BOARD CONTACTOR Figure 7 T/C (BLU) 2 PIN CONNECTOR RELAY (ORG) TO ECO 6 – Wire + T/C RELAY (ORG) TO RELAY COIL Figure 8 L1 POWER (BLK) FROM RELAY LINE SIDE EX 284 TRIAC (BLK) EL/L (BLK) ELEMENT RING L2-N POWER (RE FROM RELAY LINE SIDE...