Table of Contents
Advertisement
Using the menus 1 (Continued)
Default setting 2 menu
Item
Projection
Sets projection mode in accordance with Placement Style.
mode
(Standard)
Fan mode
Sets the cooling fan speed.
Remote control When 2 projectors are used and controlled by the remote control respectively,
this menu sets the code for the projector and the remote control.
[
or
: Enter setting]
[
:Select OK to end
Press [Cancel] to return.
Key lock
Lock the control panel buttons.
[
or
: Enter setting]
[
:Select OK to end
Press [Cancel] to return.
Lamp power
Set the lamp power.
Reset all
Press
. (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings.
Password
Password setting
p.33
Press
.
Password registration/Password setting
Detailed description
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise
gets louder.) Set this option to use the projector, for example, at high altitude (over 1,500
meters above sea level).
•
Do not set Fan mode to [High] when using the projector at a lower altitude.
[Remote control]
Sets a remote control code from 2 types. You can set each code respectively for up to
2 projectors. The factory setting is [1].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
•
You cannot operate the remote control if the codes of the projector and the remote
control do not match.
Remote control code setting for remote control
Set the same remote control code switch as the projector.
Description
p.21
(Rear)
(Ceiling)
Standard
[
]
[
: Confirm]
: Select from 1, 2
]
[
: Select On/Off
]
[
: Confirm]
]
Low
Standard
Yes
p.16 p.17
42
[Key lock]
Protect from operating errors by locking on the control panel buttons of the projector.
(The remote control operations are available.)
Control panel operations are locked after the setting is done, and accordingly operation
(Rear ceiling)
with the control panel buttons is disabled.
To release the key lock, set the [Key lock] to [Off] using remote control. Pressing
•
High
the [RETURN] button on the projector for 10 seconds also sets the [Key lock] to [Off].
(When operating the main unit, the 2 indicators of LAMP and TEMP light orange
for 3 seconds, and at the same time the projector beeps.). However, when Network
or USB memory input is selected, the [Key lock] cannot be set to [Off] with the
[RETURN] button on the projector.
[Lamp power]
When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling
fan noise gets quieter.
Displaying Information (Status display)
■
This displays information about the input signal, lamp use time, etc.
No
Item
Input
Mode name
Resolution
Frequency
Sync
Signal format
Video mode
Lamp time
Lamp reset count
Total time
Version
Notes
1:
The mode of supported RGB signals
2:
Sync signal polarity shown as P (positive) or N (negative) for [H/V].
Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be
3:
used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000
hours, consult with a dealer about getting replacement for: TLPLW23 (sold separately).
4:
[Version] shows the version of the projector's internal control program. This version will
be requested for customer service purposes.
Note
•
The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
"Yes": displayed, "No": not displayed
Digital
Analog
Description
RGB Y/P
/P
RGB Y/P
B
R
Input source name
Yes Yes Yes Yes Yes Yes Yes Yes
[Note 1]
RGB input mode
Yes No Yes No
Resolution (in dots)
Yes No Yes No
Sync frequency
Yes No Yes No
[Note 2]
Sync signal polarity
Yes No Yes No
Y/P
/P
signal format
No Yes No Yes No
B
R
Color method of video signal
No
No
No
[Note 3]
Time of lamp use
Yes Yes Yes Yes Yes Yes Yes Yes
The count for lamp replacement Yes Yes Yes Yes Yes Yes Yes Yes
The total time that this
Yes Yes Yes Yes Yes Yes Yes Yes
projector is used.
[Note 4]
Firmware version
Yes Yes Yes Yes Yes Yes Yes Yes
is shown.
p.97
43
USB
Video S-video Network
memory
/P
B
R
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No Yes Yes No
No
Advertisement
Table of Contents
