Table of Contents
Advertisement
IMPORTANT SAFETY INSTRUCTIONS (Continued)
22. Replacement Parts
When replacement parts are
required, be sure the service
technician has used replacement
parts specified by the manufacturer
or have the same characteristics
as the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
(Only the replacement of the lamp
should be made by users.)
23. Safety Check
Upon completion of any service
or repairs to this product, ask
the service technician to perform
safety checks to verify that the
product is in proper operating
condition.
24. Do not leave thermal-
paper documents or easily
deformed items on top
of the unit or near the air
exhaust for long periods of
time.
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
25. Do not use the product
in a closed installation
location.
Do not place the product in a box
or in any other closed installation
location. Otherwise it may
overheat, which could result in a
risk of fire.
26. Do not look into the laser
light source of the remote
control or direct the laser
pointer toward a person or
a mirror.
The laser beam may cause
damage to the eyesight.
27. When using a wireless LAN
function:
• Do not use near people
with heart pacemakers.
• Do not use near electronic
medical equipment, or in
hospitals or other medical
institutions.
• Do not use inside aircraft
or in places where the
wireless LAN function
could interfere with
electromagnetic signals.
The electromagnetic interference
could cause a malfunction,
resulting in an accident.
28. If the use of a wireless
LAN function interferes
with another device's
electromagnetic signals,
cease use immediately.
The electromagnetic interference
could cause a malfunction,
resulting in an accident.
8
POWER SUPPLY INFORMATION
If your line voltage is 0 to 40 V, use one of the following types of cable/plug.
Plug
configuration Plug type
Line voltage
EURO
0 – 40 V
UK
0 – 40 V
Use a 5 A fuse which is approved by
ASTA or BSI to BSI6.
Always replace the fuse cover after
changing the fuse.
IMPORTANT PRECAUTIONS
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on the
lens and the crucial internal parts. Do not use the unit for at least hours when there is an
extreme or sudden change in temperature to prevent the unit from possible damage.
Place and Manner of Installation
•
Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the projector.
•
Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts, shortening
their lives, and darkening the screen.
•
Do not use this product in the upright position or tilt it up or down by more than 0° from
level. Doing so may cause a failure or shorten the life of the product.
•
Using this instrument near a TV or radio may cause interference to the images or audio
sound. If this happens, move it away from the TV or radio.
•
Moving the projector from a low-temperature room to a high-temperature room may cause
condensation on the lens or internal parts. If you continue to use it in that situation, it may
malfunction. Wait until the condensation naturally disappears.
•
In a high altitude location where air is thin, cooling efficiency is reduced so use the
projector with [Fan mode] set to [High].
•
Only plug the power cord into outlets rated for use with the power cord's specified voltage
range. Do not overload extension cords or power strips as this can result in fire or electric
shock.
•
Route the power cable or the connecting cable away from where people could trip over it.
The projector may fall down, which could result in severe injury.
•
Be sure the power cord is easily reached for unplugging in case of emergency. Do not
place any obstacles near a wall outlet in which the cord is plugged.
Plug
configuration
Plug type
Line voltage
Australian
00 – 40 V
40 V
10 A
Switzerland
00 – 40 V
40 V
6 A
North American
00 – 40 V
40 V
15 A
p.42
9
Advertisement
Table of Contents
