Table of Contents
Advertisement
OWNER'S MANUAL
High Efficiency Electric Convection Oven
An Employee Owned Company
35 Garvey Street
Everett
●
Tel: (617) 387-4100
●
Toll Free: (866) 698-3188
Customer Service: custserv@mfii.com
MODELS:
MA
02149-4403
●
●
Fax: (617) 387-4456 (MA)
Outside MA Fax: (800) 227-2659
●
Visit Us At: www.mfii.com
●
2600 HE
●
2800 HE
●
2692 HE
●
2892 HE
●
Form No. S-5198
03/07
●
Advertisement
Table of Contents
Related Manuals for Market Forge Industries 2600 HE
Summary of Contents for Market Forge Industries 2600 HE
- Page 1 OWNER’S MANUAL High Efficiency Electric Convection Oven MODELS: 2600 HE ● 2800 HE ● 2692 HE ● 2892 HE ● An Employee Owned Company 35 Garvey Street Everett 02149-4403 Form No. S-5198 03/07 ● ● ● ● Tel: (617) 387-4100 Fax: (617) 387-4456 (MA) ●...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INSTALLATION INSTALLATION INSTRUCTIONS ............1 DETAILS & DIMENSIONS ..............2 ASSEMBLY INSTRUCTIONS - 28” MODULAR STAND .....3 ASSEMBLY INSTRUCTIONS - STACKED OVENS ON STAND ..4 ASSEMBLY INSTRUCTIONS - 7” STAND ..........5 WIRING DIAGRAMS ................6-16 OPERATION OPERATING INSTRUCTIONS ............17 CONTROL PANEL COMPONENTS ............17 MAINTENANCE PREVENTIVE MAINTENANCE ............18 REMOVAL &... -
Page 3: Installation Instructions
INSTALLATION For single oven installation on 28” stand use figure 1 for stand assembly. For stacked ovens in- stalled on a 7” stand see figure 2 for stacking instructions and figure 3 for stand assembly. Mount oven on stand. Secure to stand using 3/8” - 16 x 3/4” hex. hd. screws (P/N 10-2034) and four 3/8”... -
Page 4: Installation
INSTALLATION DETAILS & DIMENSIONS SERVICE CONNECTIONS NOTES: Allow 2” space from side wall and 2” space from rear wall if adjoining wall is com- Electrically Operated bustible. Electrical Connection- for incoming power supply wires on terminal block. All stands are 32” front to back. When used with deep oven overhang may either front or back as desired (recommended overhang is Power Supply- 1 3/4”... -
Page 5: Assembly Instructions - 28" Modular Stand
INSTALLATION ASSEMBLY INSTRUCTIONS FOR 28” MODULAR (SINGLE OR MULTIPLE) OVENS STAND: (Figure 1) Insert adjustable foot (#5) to leg assembly (#4). Assemble leg assembly (#4) to top frame assembly (#1) using hardware (#6 & #7). Place into position front and rear channel assembly (#2) and side channel (#3). Use hardware (Item #7) plain washer and (Item #6) 3/18-16 hx. -
Page 6: Assembly Instructions - Stacked Ovens On Stand
INSTALLATION IMPORTANT NOTE: If stacked ovens are adjacent to moisture produc- ing equipment (i.e. kettles or steam cookers) it is necessary to seal the seam between the stacked ovens and the moisture producing equip- ment to prevent condensation from entering control section of the bottom oven. -
Page 7: Assembly Instructions - 7" Stand
INSTALLATION Figure 3 ASSEMBLY INSTRUCTIONS 7” STAND FOR MODULAR STACKED OVENS: (Figure 3) Screw legs (#4) into top frame assembly (#1). Drop front and rear angle assembly (#2) and side angle (#3) over top frame assembly (#1). “OBSOLETE” STAINLESS STEEL ITEM # *PAINTED PART # PART #... -
Page 8: Wiring Diagrams
INSTALLATION Figure 1W... - Page 9 INSTALLATION Figure 2W...
- Page 10 INSTALLATION Figure 3W...
- Page 11 INSTALLATION Figure 4W...
- Page 12 INSTALLATION Figure 5W...
- Page 13 INSTALLATION Figure 6W...
- Page 14 INSTALLATION Figure 7W...
- Page 15 INSTALLATION Figure 8W...
- Page 16 INSTALLATION Figure 9W...
- Page 17 INSTALLATION Figure 10W...
- Page 18 INSTALLATION Figure 11W...
-
Page 19: Operation
OPERATION Do not attempt to operate oven without first reading the CONTROL PANEL COMPONENTS: following instructions thoroughly. Be sure that power is available to unit. Interior Light Switch: This switch controls the interior oven lights. These are special heat resistant 120 volt lamps. Proper Be sure that both the blower guard and deflector are replacements are available through the factory. -
Page 20: Preventive Maintenance
MAINTEANCE PREVENTIVE MAINTENANCE Thermostat Calibration If the oven components are operating but the unit is not cook- A good preventive maintenance program in the form of daily ing properly, the thermostat may need calibration. To calibrate, cleaning procedures is outlined in the following steps. proceed as follows: Remove oven shelves and wash in mild detergent and Attach a thermocouple lead to the bulb of the thermostat... - Page 21 MAINTEANCE Figure 4 Figure 5...
-
Page 22: Illustrated Parts
ILLUSTRATED PARTS Figure 6... -
Page 23: Modular Electric Oven Exploded View
ILLUSTRATED PARTS Figure 7... - Page 24 ILLUSTRATED PARTS Figure 7 (see page 21) STANDARD DEEP ITEM # PART # PART # DESCRIPTION 99-1570 99-1569 TOP PANEL 99-1574 99-1578 L.H. PANEL ASSY 99-1576 99-1580 R.H. PANEL ASSY 99-1572 99-1572 REAR PANEL 10-1295 10-1296 L.H. RACK SUPPORT 10-1295 10-1296 R.H.
-
Page 25: Modular Electric Oven Heating Elements
ILLUSTRATED PARTS Figure 8... - Page 26 ILLUSTRATED PARTS Figure 8 (see page 23) ITEM PART # DESCRIPTION INSIDE OVEN LINER (STYLE B): 10-6084 HEATING ELEMENTS, STANDARD, 3100 WATTS, 208V 10-6085 HEATING ELEMENTS, STANDARD, 3100 WATTS, 230V 10-6086 HEATING ELEMENTS, STANDARD, 3100 WATTS, 440/479V 10-6087 HEATING ELEMENTS, STANDARD, 3100 WATTS, 480V 10-6678 HEATING ELEMENTS, DEEP, 4000 WATTS, 208V 10-6843 HEATING ELEMENTS, DEEP, 4000 WATTS, 230V 10-6844 HEATING ELEMENTS, DEEP, 4000 WATTS, 440/479V...
-
Page 27: Electric Control Panel
ILLUSTRATED PARTS Figure 9 Figure 9 ITEM ITEM PART # DESCRIPTION PART # DESCRIPTION 99-3049 CONTROL PANEL ASSY 10-6280 CIRCUIT BREAKER “COMPLETE” 10-4472 CONTROL KNOB 10-6264 ON-OFF TOGGLE SWITCH 99-3027 NAMEPLATE PANEL 10-5016 PILOT LIGHT 10-6415 NAMEPLATE BEZEL 10-6267 LIGHT RESET, 208/230V 10-4714 THERMOSTAT 10-6270 LIGHT RESET, 440/480V...