OWNER’S MANUAL PREMIER SERIES HIGH PERFORMANCE ELECTRIC CONVECTION OVEN MODELS: m 3000 m 3092 WARNING: FOR YOUR SAFETY: Improper installation, adjustment, alteration, service Do not store or use gasoline or other flam- or maintenance can cause property damage, injury mable vapors or liquids in the vicinity of this or death.
INTRODUCTION IMPORTANT: Service of the equipment should be performed by qualified personnel who are knowledgeable with Safe and satisfactory operation of your equipment Market Forge cooking equipment. depends on proper installation. Installation must conform with local codes, or in the absence of local codes, the Natonal Electrical Code, (ANSI NFPA-70 Latest Edition).
GENERAL IMPORTANT: SINGLE OVEN: To perform maintenance and repairs of the ap- Assemble the leg/stand assembly as follows: pliance, please contact the factory, factory repre- 1. Remove legs from package. sentative, or the nearest local authorized service 2. Secure top frame parts to the legs with bolts company.
ASSEMBLY STACKING INSTRUCTIONS MODEL 3092 OVENS STEP 1. Attach (4) foot mounting plates and (4) bullet feet onto bottom ove. Set top oven in place on top of bottom oven and slign them in place. STEP 2. Fasten rear mounting plates as shown. STEP 3.
IMPORTANT LEVELING: FINAL PREPARATION: A carpenter’s level should be placed on the oven’s On initial installation, turn the oven to 250 and op- center baking rack and the unit leveled both front- erate for about 1 hour, then reset the thermostat to to-back and side-to-side.
CLEANING & MAINTENANCE DAILY CLEANING: with a liquid cleaner designed for this material at OVENS: the end of each day. 1. Remove the baking racks. Wash in hot soapy water and replace after the rest of the oven is DO NOT USE steel wool, abrasive cloths, cleaners cleaned.
SPECIFICATIONS (SINGLE OVEN) MODEL: 3000 CLEARANCE REQUIRED: CLEARANCE REQUIRED: When installing ovens against combustable surfaces 6” (152mm) clearance is required. When installing ovens against combustable surfaces 6” 152mm clearance is required. When installing ovens against non-combustable surfaces (rear or side walls) 0” clearance is required. When installing ovens against non-combustable surfaces (rear or side walls) 0”...
SPECIFICATIONS (STACKED OVEN) MODEL: 3092 CLEARANCE REQUIRED: When installing ovens against combustable surfaces 6” (152mm) clearance is required. When installing ovens against non-combustable surfaces (rear or side walls) 0” clearance is required. SERVICE CONNECTIONS Electrically Operated Electrical Connection - Connection for incoming power supply wire on terminal block.
Page 12
PARTS LIST ITEM # PART # DESCRIPTOPM QTY. 93-0025 MOTOR 93-0026 MOTOR BRACKET 93-0021 LIGHT BOX 93-0022 LIGHT SOCKET 93-0020 LIGHT BULB 93-0064 LIGHT COVER 93-0067 RIGHT SIDE PANEL - REAR 93-0055 RIGHT SIDE PANEL - FRONT 93-0017 TERMINAL BLOCK (8-WAY) 93-0300 MARKET FORGE PREMIER LEXAN DECAL (CONTROL PANEL) 93-0011...
Page 13
PARTS LIST 93-0076 DIVERTER - BOTTOM 93-0077 DIVERTER - SIDES 93-0078 DIVERTER - TOP 93-0074 LEG 6” S/S - WITH ADJUSTABLE FOOT (TSCV-2) 93-0075 LEG PLATE ASSY. (TSCV-2) 93-0048 RACK GUIDE - R/H 93-0050 RACK GUIDE - L/H 93-0049 RACK 93-0069 TOP PANEL 93-0047...
Page 14
PARTS LIST Fig. 5 Heating Elements ITEM # PART # DESCRIPTION QTY. 98-4066 208 Volt Heating Elements (Nest of Three) 1 Set 98-4067 240 Volt Heating Elements (Nest of Three) 1 Set 98-4065 480 Volt Heating Elements (Nest of Three) 1 Set ITEM # PART #...
Page 15
PARTS LIST Fig. 7 Electrical ITEM # PART # DESCRIPTION QTY. 98-4098 Electrical Box 6” x 6” x 4” 98-4092 Transformer, 1KVA...
Page 16
PARTS LIST PREMIER SERIES HEAT ON THERMOSTAT ITEM # PART # DESCRIPTION QTY. 93-0300 Market Forge Premier Lexan Decal 93-0023 Thermostat 60” Capline 93-0023 Thermostat Knob REF. MODE 93-0013 Switch, Fan Hi-Lo 93-0014 Switch, Light Momentary Oven Light 93-0012 Switch Power, 3 Positions On/Off Cooldown 93-0028 Timer Knob...