Sharp CD-C811W Service Manual page 48

CD-C811W/821W
IC2 VHiLC78622N-1: Servo/Signal Control (LC78622N) (2/2)
Pin No. Terminal Name Input/Output
50* SFSY (NC)
51 SBCK
52* FSX (NC)
53 WRQ
54 RWC
55 SQOUT
56 COIN
57 /CQCK
58 /RES
59* TEST11 (NC)
60* 16M (NC)
61 4M
62 TEST5
63 /CS
64 TEST1
Note: The same potential must be supplied to the power terminals (VDD, VVDD, LVDD, RVDD, XVDD).
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
IC701 RH-iX0300AWZZ: System Microcomputer (IX0300AW) (1/2) (CD-C811W)
Pin No. Port Name
1 P94/FIP6 7G
2 P93/FIP5 8G
3 P92/FIP4 1G
4 P91/FIP3 2G
5 P90/FIP2 3G
6 P81/FIP1 4G
7 P80/FIP0 9G
8 VDD VDD
9 P27/SCK0 DO
10 P26/S00/SB1 DI
11 P25/SI0/SB0 CE
12 P24/BUSY CLK
13 P23/STB CD RWC
14 P22/SCK1 CD WRQ
15 P21/S01 CD PCCL
16 P20/SI1 CD COIN
17 RESET RESET
18 P74 CD SQOUT
19 P73 TIMER LED
20 AVss AVSS
21 P17 CD CQCK
22 P16 CD DSP RES
23 P15 CD FRF
24 P14/ANI4 A/D T2 RUN
25 P13/ANI3 A/D KEYIN 1
26 P12/ANI2 A/D KEYIN 2
27 P11/ANI1 A/D KEYIN 3
28 P10/ANI0 A/D DIST
29 AVDD AVDD
30 AVREF AVREF
Output Output terminal of synchronous signal of subcode frame. It drops when subcode stands by.
Input Clock input terminal to read subcode. Schmit input (Connected to 0V when not used.)
Output Output terminal of synchronous signal of 7.35kHz divided from quartz oscillation.
Output Output terminal to stand by output of subcode Q.
Input Input terminal of read/write. Schmit input.
Output Output terminal of subcode Q.
Input Command input terminal from microcomputer.
Input Clock input terminal to fetch command input, or pick up subcode from SQOUT. Schmit input.
Input Reset input terminal of LC78622. When turning on power, set it at "L".
Output Output terminal for test. Used in the open state ("L" output as ordinary).
Output Output terminal of 16.9344Hz.
Output Output terminal of 4.2336MHz.
Input Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V.
Input Chip selection input terminal. Pull-down resistor is integrated.
Connected to 0when not controlled.
Input Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V.
Terminal Name Input/Output
Output
Output
Output
Output
Output
Output
Output
—
Input
Output
Output
Output
Output
Input
Output
Output
Input
Input
Output
—
Output
Output
Input
Input
Input
Input
Input
Input
—
—
Function
FL Display segment driver
FL Display segment driver
FL Display segment driver
FL Display segment driver
FL Display segment driver
FL Display segment driver
FL Display segment driver
VDD
Data input
Data output
Chip enable output
Clock output
CD DSP read write cont
CD DSP write request cont
CD DSP PCCL
CD COIN (Data output)
Reset
CD SQOUT (Data input)
TIMER LED control
Analog ground
CD CQCK (Clock output)
CD DSP reset
CD RF level detection
Analog data T2 RUN
Key input 1
Key input 2
Key input 3
Key output distination
Analog VDD
Analog REF voltage
– 48 –
Function